Len69Coupe 33 Report post Posted November 15, 2018 Any tips on repairing sheet metal holes that have been stripped. Specifically talking about the door sill holes. Can't really install larger screws I don't think. I've always fixed stripped wood by inserting a toothpick and then installing a screw. I thought about trying to stick a piece of welding wire in the hole and then the screw, but I'm not sure if that work or last. The car is completely stripped right now and I thought maybe weld the holes up and drill them back out. Seems like a PIA though. Any tips? Quote Share this post Link to post Share on other sites
Cantedvalve 128 Report post Posted November 15, 2018 You have nailed the correct way of fixing them. Weld and redrill. You COULD do an expoxy instead of welding, but if the car is completely stripped, why not do it right? I will be doing the epoxy as my car is NOT stripped down right now, otherwise I would weld. Bandaid fixes include some sort of thick but malleable goo that can help old the screw in place. Maybe larger screws. Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted November 15, 2018 All you need to do is buy the next size larger screw. WURTH sells them. I have done this over 100 times. Bear in mind that they sell them with two different size head choices. 2 1969_Mach1 and RPM reacted to this Quote Share this post Link to post Share on other sites
Len69Coupe 33 Report post Posted November 15, 2018 Cantedvalve, I was truly hoping there was an easier way, probably because I'm lazy. Not really, LOL. barnett468, I was thinking going to larger screw wouldn't work because of the size of the hole in the sill plates. Wouldn't a larger screw not fit in the plate properly. I don't know what a Wurth is? Online store? Quote Share this post Link to post Share on other sites
Cantedvalve 128 Report post Posted November 15, 2018 I'm right there with you Len. I think this is Wurth: https://www.wurthusa.com/ 1 Len69Coupe reacted to this Quote Share this post Link to post Share on other sites
BuckeyeDemon 211 Report post Posted November 15, 2018 I can't remember if those are small slotted holes, but if not, consider putting in a rivut nut (or equivalent) and a matching fastener. 1 Len69Coupe reacted to this Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted November 15, 2018 We weld them up, and drill the correct size. Going with a bigger screw looks butt ugly :( 1 Len69Coupe reacted to this Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted November 15, 2018 16 hours ago, mustangstofear said: We weld them up, and drill the correct size. Going with a bigger screw looks butt ugly :( no it does not if you use the screws i mentioned because the head size is not any larger than the original screw. i have installed hundreds of these special oversized screws and many were in concourse mca judged cars. 1 RPM reacted to this Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted November 15, 2018 3 hours ago, Len69Coupe said: barnett468, I was thinking going to larger screw wouldn't work because of the size of the hole in the sill plates. Wouldn't a larger screw not fit in the plate properly. I don't know what a Wurth is? Online store? only the special one size over screws i mentioned work and look correct. i will try to find the info for you. the wurth distributor in so cal has them. 1 Len69Coupe reacted to this Quote Share this post Link to post Share on other sites
larryc94 38 Report post Posted November 16, 2018 They have screws for this exact problem. The head is the correct size the threaded portion is larger https://www.npdlink.com/product/mounting-kit-scuff-plate-repair-screws-for-oversized/100127?backurl=search%2Fproducts%3Fsearch_terms%3Ddoor%2Bscuff%2Bplate%26top_parent%3D1%26year%3D1970&year=1970 2 RPM and Len69Coupe reacted to this Quote Share this post Link to post Share on other sites
Len69Coupe 33 Report post Posted November 16, 2018 I'm definitely willing to try the screws, as long as they don't look butt ugly like mustangstofear said. If I can't get them to look right I'll weld the holes and re-drill. Thanks for all the help guys. Len Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted November 16, 2018 They don't state the size from NPD. We have a special #8 screw made with a #6 head. Normally a #6 head screw cost 7 cents, these cost us 1.00 each :( Quote Share this post Link to post Share on other sites
aslanefe 333 Report post Posted November 16, 2018 40 minutes ago, mustangstofear said: They don't state the size from NPD. We have a special #8 screw made with a #6 head. Normally a #6 head screw cost 7 cents, these cost us 1.00 each :( Why not buy them from NPD, they are $1 for 4 of them. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted November 16, 2018 Because ours application requires a flat head. Quote Share this post Link to post Share on other sites
larryc94 38 Report post Posted November 16, 2018 Those screws installed look no different than the original screw Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted November 17, 2018 12 hours ago, Len69Coupe said: I'm definitely willing to try the screws, as long as they don't look butt ugly like mustangstofear said. Once again...the screws I mentioned look like the originals. They may also be the same screws that npd is selling but I for one do not know if they are. 3 RPM, Len69Coupe and 1969_Mach1 reacted to this Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted November 17, 2018 On 11/15/2018 at 8:47 AM, barnett468 said: All you need to do is buy the next size larger screw. WURTH sells them. I have done this over 100 times. Bear in mind that they sell them with two different size head choices. I did this fix with the cowl vent front edge screws. Easy peasy. As b468 says, the thread portion is larger, but the head remains the same size. On the cowl vent, the holes were big enough that they didn't need to be enlarged. Seems like a pretty simple fix to me. Quote Share this post Link to post Share on other sites
Midlife 814 Report post Posted November 20, 2018 I found an elegant, but backyard fix for this. Use the plastic sleeve for drywall screws that you use for hanging pictures, and stuff the sleeve down the enlarged hole. The sill plate covers up the visual appearance of it, and you can use the original size screw. Quote Share this post Link to post Share on other sites
aslanefe 333 Report post Posted November 20, 2018 Welcome back online Midlife. Quote Share this post Link to post Share on other sites
Brian Conway 264 Report post Posted November 20, 2018 2 hours ago, Midlife said: I found an elegant, but backyard fix for this. Use the plastic sleeve for drywall screws that you use for hanging pictures, and stuff the sleeve down the enlarged hole. The sill plate covers up the visual appearance of it, and you can use the original size screw. Excellent solution. I used this method for one of my ext. door mount mirrors. Brian Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted November 20, 2018 On 11/16/2018 at 7:11 AM, mustangstofear said: Because ours application requires a flat head. I might be wrong, but I believe the sill plates use what is called an oval head screw not a flat head screw. Quote Share this post Link to post Share on other sites
aslanefe 333 Report post Posted November 20, 2018 35 minutes ago, 1969_Mach1 said: I might be wrong, but I believe the sill plates use what is called an oval head screw not a flat head screw. I believe they have their own design sill plates which uses a flat head screw. Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted November 20, 2018 19 minutes ago, aslanefe said: I believe they have their own design sill plates which uses a flat head screw. Oh, okay, that makes sense. Quote Share this post Link to post Share on other sites