Mike65 476 Report post Posted May 18, 2018 What does everyone think would be the best cleaner to use to clean the rest of the sealer that I can not scrape off the body where the front windshield will sit?. Quote Share this post Link to post Share on other sites
mwye0627 44 Report post Posted May 18, 2018 If they sealed it with urethane windshield mounting adhesive, I know of no cleaners or solvents that will touch it... In the body shop, we just keep at it with blades and scrapers until we get down to metal, then if re-installing a windshield with urethane, we use a special primer that allows the urethane to bond directly to metal. Quote Share this post Link to post Share on other sites
Ridge Runner 1,113 Report post Posted May 18, 2018 Wire wheel and a die grinder for urethane scraps ,i use gas on a wrag for sealers because it doesnt evaporate as fast as acetone ...dont set your self on fire though 1 mwye0627 reacted to this Quote Share this post Link to post Share on other sites
moodster 55 Report post Posted May 18, 2018 Lacquer thinner will take it off. david Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted May 19, 2018 it it is not urethane, simple paint thinner with lots of paper towels will eventually remove it. both acetone and lacquer thinner dry much more quickly and are much harsher on the paint. if it has never been removed before, it is not urethane. gas fumes are a bit more unhealthy and unpleasant to smell. Quote Share this post Link to post Share on other sites
Mike65 476 Report post Posted May 19, 2018 Here is what the sealer looks like after I scraped most of it off the body. Quote Share this post Link to post Share on other sites
Ridge Runner 1,113 Report post Posted May 19, 2018 3 hours ago, barnett468 said: it it is not urethane, simple paint thinner with lots of paper towels will eventually remove it. both acetone and lacquer thinner dry much more quickly and are much harsher on the paint. if it has never been removed before, it is not urethane. gas fumes are a bit more unhealthy and unpleasant to smell. Sorry ,had a burito for lunch Quote Share this post Link to post Share on other sites
Midlife 814 Report post Posted May 19, 2018 Ahhh...but if you use racing fuel (110 octane), the smell will be much better! I used gasoline dipped in a rag to remove aftermarket undercoating on my car, along with a small flat screwdriver to get into nooks and crannies. Of all of the solvents available, gasoline is the cheapest and very effective. Just work in a reasonably well-ventilated area and keep the gas in a metal oil catch pan outside. Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted May 19, 2018 if you don't have a wire wheel etc, buy a gasket scraper. you need to get a lot more of that off before you try to remove the residue. Quote Share this post Link to post Share on other sites
Mike65 476 Report post Posted May 19, 2018 I have a gasket scraper which I have been using to get it almost to a clean body I was asking about the remainder that will not come off with the scraper, so Ridge Runners idea of the wire wheel should work. Thanks Ridge. barnett I know that I can not remove what is left there with a solvent. Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted May 20, 2018 1 hour ago, Mike65 said: I have a gasket scraper which I have been using to get it almost to a clean body I was asking about the remainder that will not come off with the scraper, so Ridge Runners idea of the wire wheel should work. Thanks Ridge. barnett I know that I can not remove what is left there with a solvent. post a photo of your gasket scraper. i can get most if that off with my gasket scraper but may need to use a screw driver for some of it. you will NOT get the thick pieces off with any type of solvent or gas unless you pour it on and lite it on fire. 1 Caseyrhe reacted to this Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted May 20, 2018 Looks like you're taking it down to bare steel ? In the auto glass world It's all done with short and long knives that use utility blades. Once you have it cleaned be sure to use some Epoxy primer, not automotive pinchweld, because it's not designed for bare metal. Quote Share this post Link to post Share on other sites
Mike65 476 Report post Posted May 20, 2018 21 hours ago, barnett468 said: post a photo of your gasket scraper. i can get most if that off with my gasket scraper but may need to use a screw driver for some of it. you will NOT get the thick pieces off with any type of solvent or gas unless you pour it on and lite it on fire. Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted May 21, 2018 i use the red handle one but mine is as sharp as a razor. if it is dull it is worthless. i also use a narrow wood chisel around 5 1/6" - 3/8" wide. i never, ever, use the razor blade ones. Around $8.00 at home depot. Quote Share this post Link to post Share on other sites
JayEstes 172 Report post Posted May 23, 2018 As long as there is no paint around you are worried about getting ruined, after using a scraper, and a wire brush where I could, I used a scotchbrite pad soaked in lacquer thinner ("cleanup thinner" at your local paint store). As I go I have a roll of paper towels to do the final wipe down, once I get the stuff off. A gallon of thinner will go a long ways and is about $10. Scotchbrite with this solvent is "super effective" on just about anything you put it on. The scratching effects of the pad combined with the thinner are an amazing pair. It's messy, and make sure there is no good paint nearby, cause it will ruin just about any applied paint. Good luck finding any gloves that will protect your hands from this. thick PVC gloves are probably best. Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted May 23, 2018 I've used mineral spirits to remove residue. At least when I've done it, the mineral spirits softens the residue and it comes off easily. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted May 23, 2018 We use mineral spirits all the time, but it won't remove urethane only butyl . 1 mwye0627 reacted to this Quote Share this post Link to post Share on other sites
Vicfreg 773 Report post Posted May 26, 2018 You could use a propane fired handheld torch (like you use for copper plumbing) to preheat the material and scrape it out. Welding gloves and nearby fire extinguisher recommended..... Quote Share this post Link to post Share on other sites
Mike65 476 Report post Posted May 26, 2018 15 hours ago, Vicfreg said: You could use a propane fired handheld torch (like you use for copper plumbing) to preheat the material and scrape it out. Welding gloves and nearby fire extinguisher recommended..... Thanks Vic, that is what I used to soften the sealer to get the windshield out the the majority of the rest of the sealer off the body. Quote Share this post Link to post Share on other sites