Grabber70Mach

Medallions on, rear deck stripe on. Sent pics to my brother, he may not be able to sleep tonight, lol. 

Laid out the striping tape for stripes, just forgot to pick up the ivory soap to apply them

Installed screw in rivets for side medallions 

Rear fin, trunk weatherstrip, and trunk cleaned out. 

I like'em! These will go in my car. Long awaited. 

The RTX ones are finally available:
https://www.dakotadigital.com/index.cfm/page/ptype=product/product_id=1221/category_id=434/mode=prod/prd1221.htm
 
Sorry, I missed your post Grabber70Mach

The only wires on my AAW setup that go from the steering column connector to the DD box are for the left and right turn signals.
These are AAW wires 14A,B (Lt Blue) and 15A, B (dark Blue)
14A, B hooks to the Ford column wire that is Green with a White Stripe
15A, B hooks to the Ford column wire that is White with a Blue Stripe
14A goes to DD box #31 (my number)
15A goes to DD box #30 (my number)

Attention @Mach1 Driver they are up:
https://www.dakotadigital.com/index.cfm/page/ptype=product/product_id=1221/category_id=706/mode=prod/prd1221.htm

@Mach1 Driver As of today I was told to look at the website in two weeks.  They should be available at that time.

Blinkers working. 
Ford already leading the charge on “heads up display” back in 69
8CA982C9-CC81-4C79-8ADB-46D8ABA7ABC7.MOV

@Mach1 Driver As of today I was told to look at the website in two weeks.  They should be available at that time.

Thanks Bob, someday I'll be able to retire, do what I really love, and at a reasonable cost to make someone else's dream a reality.

Finished up with the radio and trim, just a little more work on the door panels and interior is totally done.
Hard to find good help these days, too!

Hood not latched in this pic ,but Like this ?

I have a Mach 5...
 
Go Speed Racer......
 
 

Oh, all of my wiring going upfront is routed through the fenderwells
 

I have a lot of posts on my AAW install in my 1970 convertible on my thread.  To answer your question, you use the Dakota wiring harness and plugs as they have water temperature and oil pressure senders that come with their kit.  For the AAW wiring, you should still route the blue and green wires (#31 and #35) to the front of the car, and save them as spares.  I used them for transmission and oil temperature gauges I put in my console.  Wires 31 and 35 go to connector AAW connector "F".    Connector F is designed to be used to feed the original Mustang dash area, so I repurposed most of that wiring.
The fan wire (#300) is fed from the fuseblock ("fan") and is a key-on-hot power feed.  You can use that for any accessory you may have that needs power when the ignition switch is in "run".  I used this for the power feed to my PWM fan controller, not my fan, as it was not large enough for that.
I have a detailed spreadsheet and block diagrams I used which may help you. I will send that along if you need it.
My advice is to not install the harness until you plan where every wire will go to and from.  It will save you rework later.  it is not a "plug and play" harness.
I also wrapped the harness once I had figured out where all the wires would go. I have attached some pics of the install. Good luck
 
 
 

That was kinda cool. I realize my Mach is pretty  beat up, but you don't see many originals...

I use every bit of it. I don’t think you could ever make it too big!

Pretty cool pic from last night. Mike working in blaster with car in foreground at night!
 

I don't like that aluminum door panel one bit.
That car needs to be wired about now...

Don't know if this will help others but I tried some things and even though yes the most recent gallery was disabled I found a back door into the original albums page, you have to find your album and then click through each individual pic links one by one to be able to copy and save but it's better than nothing. Obviously this won't include anything that was updated to the gallery after the albums closed but it's an option.
http://1969stang.com/albums/
 

I hope so- I've been getting stall tactics for over a year

I emailed Dakota Digital about the RTX for the 69-70 Mustangs a couple days ago. They told me to check back at the end of September and they will have more information.

I called them about a month back asking about them.  The gentleman I talked to said they were in the prototype phase, he estimated an availability of Nov to Feb.