po51 21 Report post Posted May 14, 2015 What rear disc brake system will work with Magnum 500 wheels 15x8 with the standard 4.50 off set? I understand there is a fit issue with some of the units? Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted May 14, 2015 Check out Speed way motors.com They have some attractively priced rears that are sized to fit. http://www.speedwaymotors.com/Search?query=910-31921 Quote Share this post Link to post Share on other sites
Wycked69 20 Report post Posted May 16, 2015 You can also check out "Right Stuff" detailing out of Columbus Oh. They have a pretty nice set up that will work with you original emergency brake cable system. http://www.getdiscbrakes.com/zdcrd02z Which brings me to a couple of things you need to consider when converting rear drum to disc. Emergency Brake: Many of the conversion kits do not mention or advise how you go about installing/using your emergency brake system. Many don't always make provision for this and you will wind up having to fabricate some things (more than you may wish) Brake Lines: Your drum brakes were plumbed with hard line right up to the wheel cylinder. Your disk brakes will most likely require a flexible line between the caliper and the hard line. You may have to fabricate a bracket for mounting the flex line where it will connect to a hard line. Master Cylinder: Your master cylinder will have to be changed to match your brake set up. If all four wheels are now going to be a disc brake setup, you will need a disc/disc master cylinder. This also means your original "combo" valve arrangement may have to be changed as well to match your brake configuration. Al this being said, rear disk brakes do not do much more than provide for an appearance versus increased stopping power. Unless you are into some serious racing, I doubt you would notice any difference in stopping power. I'm not an expert, just a "been there - done that" type of opinion. 1 LiLMike reacted to this Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted May 16, 2015 . my friends manufacture their own kits that some other mustang suppliers sell. this 658 kit on page 77 may fit 15" wheels . . call for info. this 6107S kit on page 78 fits 14" and up wheels. http://www.abspowerbrake.com/maincatalog_frameset010.html you will need an adjustable proportioning valve and a dual disc master cylinder with probably a 7/8" - 15/16" master if they are manual. if you have factory discs, you must bypass the factory proportioning valve and still install the one above. . Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted May 16, 2015 You can also check out "Right Stuff" detailing out of Columbus Oh. They have a pretty nice set up that will work with you original emergency brake cable system. http://www.getdiscbrakes.com/zdcrd02z Which brings me to a couple of things you need to consider when converting rear drum to disc. Emergency Brake: Many of the conversion kits do not mention or advise how you go about installing/using your emergency brake system. Many don't always make provision for this and you will wind up having to fabricate some things (more than you may wish) Brake Lines: Your drum brakes were plumbed with hard line right up to the wheel cylinder. Your disk brakes will most likely require a flexible line between the caliper and the hard line. You may have to fabricate a bracket for mounting the flex line where it will connect to a hard line. Master Cylinder: Your master cylinder will have to be changed to match your brake set up. If all four wheels are now going to be a disc brake setup, you will need a disc/disc master cylinder. This also means your original "combo" valve arrangement may have to be changed as well to match your brake configuration. Al this being said, rear disk brakes do not do much more than provide for an appearance versus increased stopping power. Unless you are into some serious racing, I doubt you would notice any difference in stopping power. I'm not an expert, just a "been there - done that" type of opinion. All good points that need to be considered. However, I believe a rear disc conversion is an easier job than doing one rear drum brake job. Quote Share this post Link to post Share on other sites
shaun071 62 Report post Posted May 17, 2015 Something else to consider is readily available pads and rotors for the conversion. If a pad or rotor goes bad you want to be able to go to a local parts store and get one off the shelf. This is what made me choose a locally made kit adapting aussie falcon rear brakes. Quote Share this post Link to post Share on other sites
po51 21 Report post Posted May 18, 2015 Thanks for all of your input, I think I'm staying with my drum brakes, getting new drums and better shoes. Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted May 18, 2015 Thanks for all of your input, I think I'm staying with my drum brakes, getting new drums and better shoes. try ebc and centric for shoes Quote Share this post Link to post Share on other sites
70769 18 Report post Posted May 18, 2015 I didn't know ebc made shoes... SWEEET! Quote Share this post Link to post Share on other sites
lanky 44 Report post Posted May 18, 2015 In general I would stay away from anything that uses 80's single piston gm calipers. I looked at those they use at speedway and they are the same that I have dealt with on my cutlass, garbage... the sliding mechanism is inherently flawed and the pistons have reputations for sticking and acting weird. My $.02 1 cobragary reacted to this Quote Share this post Link to post Share on other sites
Sampa 0 Report post Posted July 10, 2015 I'm hoping to find a kit to adapt SN99 Mustang rear calipers to a '69 9" flange. I converted to a Fat Man coil over strut front suspension and use SN99 dual piston calipers. I like using Ford parts on a Ford and also parts that you can get a hold of easily when you need them. Quote Share this post Link to post Share on other sites
SM69Mach 68 Report post Posted July 10, 2015 I used Street or Tracks kits that uses the SN95 Rear brake calipers. Quote Share this post Link to post Share on other sites
Sampa 0 Report post Posted July 11, 2015 I used Street or Tracks kits that uses the SN95 Rear brake calipers. Hey it sounds like you've already done what I've been looking for. I want to adapt SN99 (like SN95 but later technology) to the 9" on my '69. What products did you use? I also see there is a kit from Mustang Steve that "will" adapt calipers/rotor from a S197 ('05 - '10 Mustang). Do you have any experience or opinions these? Quote Share this post Link to post Share on other sites
SM69Mach 68 Report post Posted July 12, 2015 This is similar to the kit I bought from Street or Track a couple of years ago. I didn't buy the calipers as I already had them. http://www.streetortrack.com/Street-or-Track-11.65-Rear-Disk-Brake-Kit-pr-23990.html Just pulled off the drum brakes, and put on the new brackets and it all bolted right up. I ended up not changing MC and installed a proportioning valve to adjust the rears. Been running it this way for a couple of years now with no issues. Hope that helps. Quote Share this post Link to post Share on other sites
Sampa 0 Report post Posted July 12, 2015 This is similar to the kit I bought from Street or Track a couple of years ago. I didn't buy the calipers as I already had them. http://www.streetortrack.com/Street-or-Track-11.65-Rear-Disk-Brake-Kit-pr-23990.html Just pulled off the drum brakes, and put on the new brackets and it all bolted right up. I ended up not changing MC and installed a proportioning valve to adjust the rears. Been running it this way for a couple of years now with no issues. Hope that helps. This sure looks like what I'm looking for. Thank you!! I'll contact them to see about just getting the all the critical stuff without the calipers. Is their rotor different from an SN95? I wonder if it's compatible with SN99 calipers? Quote Share this post Link to post Share on other sites
SM69Mach 68 Report post Posted July 13, 2015 This sure looks like what I'm looking for. Thank you!! I'll contact them to see about just getting the all the critical stuff without the calipers. Is their rotor different from an SN95? I wonder if it's compatible with SN99 calipers? I am not sure what he is currently using for his kits. I bought my stuff a few years ago in including the front disc brake bracket for disc spindles which I don't think he sells separately any more, so not really sure what he is using. I am using the SN95 caliper with bear Cobra brakes on my setup. I would just give him a call, really cool guy to talk Quote Share this post Link to post Share on other sites
Footcutter11 23 Report post Posted July 13, 2015 I used 2005 Mustang calipers, rotors, and 1.25" spacer. Got a caliper mount on ebay for the conversion. Still required some material removal from the caliper, but they work great. Much cheaper solution. Think I spent about ~$160. Took about 6 hours. Quote Share this post Link to post Share on other sites
Sampa 0 Report post Posted July 14, 2015 I used 2005 Mustang calipers, rotors, and 1.25" spacer. Got a caliper mount on ebay for the conversion. Still required some material removal from the caliper, but they work great. Much cheaper solution. Think I spent about ~$160. Took about 6 hours. I believe I saw that from Mustang Steve's eBay site. You are right, the price is much cheaper. Having owned an '05 for several years I never had any complaint about the rear brakes. I think I came up with about $250 for; the kit, slotted rotors and Auto Zone calipers/hoses. What kind of master cylinder and booster are you running? Quote Share this post Link to post Share on other sites
Footcutter11 23 Report post Posted July 14, 2015 Wilwood master cylinders, one for the front, and one for the rear. No booster. http://www.wilwood.com/MasterCylinders/MasterCylinderList.aspx?group=Compact%20Remote%20Flange%20Mt%20Master%20Cyl-1/8%20NPT%20Outlet 3/4" bore. Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted July 15, 2015 In general I would stay away from anything that uses 80's single piston gm calipers. I looked at those they use at speedway and they are the same that I have dealt with on my cutlass, garbage... the sliding mechanism is inherently flawed and the pistons have reputations for sticking and acting weird. My $.02 Thanks for the tip Lanky! I researched them, what a nightmare they appear to be. There wasn't too much info available on them back around 2000 when I did the conversion. I'll be looking into 94-2010 or so Mustang/Cobra rear brakes. Quote Share this post Link to post Share on other sites
Footcutter11 23 Report post Posted July 16, 2015 Thanks for the tip Lanky! I researched them, what a nightmare they appear to be. There wasn't too much info available on them back around 2000 when I did the conversion. I'll be looking into 94-2010 or so Mustang/Cobra rear brakes. I recommend the 2005 calipers. Integral parking brake. Quote Share this post Link to post Share on other sites