Caseyrhe

Hard to tell from picture, but if those are switches. We ran a few switches back in the day when street racing, to cut out alt for hp and also rear tail/brake light to avoid getting caught

I found a C6 tranny and a 9 inch 31 spline rear end on CL, 9" is supposed to be limited slip and out of a Mustang, going to check out today to measure and verify. Both have been sitting covered for 4-5 years Deal or No Deal if for a 69 Mustang

http://1969stang.com/forum/index.php?/topic/55365-1969-428-cj-main-bearings/ May check out this on the FE oiling system started by Raven in the tech section, was on the 3 page from today's....lots of good info on altering the oil passages during the build I don't have any experience with the double hump pan. PM when you get to the little things if parts needed. Thank you for your service, God's speed

Welcome, where in Texas are you located. I have a door, windshield, fender, light bucket and a few other misc parts that could save you some money

Electric Power Steering Assist??

No a lot... extensions, lights, and bumper, are secured normally. End of frame rails are still attached tail light panel. Trunk is attached with latch and tack welded straps at top/rear quarters on interior, still has weatherstrip on lid. It hangs on a J-bracket attached to stud that hooks onto the tail light panel brace.

Here it is hanging on the wall, the red rag gas cap adds charecter, you think

Original hoods are getting few and far between, have 2 right now and been offered up to 800 a piece. Just say'en

A while back I bought a Ivy Green 69 coupe for a parts car. I ask for the forum "Scap it or Save it", well I parted it out and ended up selling the shell and lots of parts for cheap so more Stangs might survive. I mentioned to the buyer of the shell what I was going to do with the rear if I didn't sale it. It ended up he had the rear of a 70 he would give me......well here it is completed. Plan to hook up some lights with motion sensor so brake lights come on, install trunk key and gas cap when the Mach is put back together and then hang it on the wall. Other cool thing is, my 70 convert is the same Green.

Prefer white, 100% cotton. I know black doesn't show grease/dirt, but who would wear either while working in their car. White is much cooler in the summer heat and would proudly wear it at while at the car shows

Thanks guys

Outside ss

Could use a measurement for the fastback pillar trim

Apparently the windshield trim moldings are different between a fastback and coupe. Need to know the length of the molding that runs vert/parallel with the pillar post so I can take the correct ones in for polishing. Are the windshields different too?

ðŸ‘

Sorry, my bad. May check this site out http://harmonclassicbrakes.com

This the one you're referring to? http://www.ebay.com/itm/1963-68-Ford-Mustang-Galaxie-Thunderbird-Power-Brake-Booster-Master-Spacer-/121972317381? hash=item1c661ddcc5:g:InIAAOSwFEFXJJRI&vxp=mtr

And a high volume pump.

Did you find the build sheet under drivers seat carpet?

You can pull together, will have to pull harm balancer to clear from support. Never pulled with headers attached, so can't help there

I have found a buyer for the shell and he is to pick it up in a couple of weeks. He is going to transfer his car over to my shell, which has good rails, boxes, and rear quarters, and a blue title in lieu of his salvage title. So feel good that the car will be saved. Eventually I will start posting the Grande parts with pictures, saving most everything else until mine and my brothers Machs are put together. Thanks for all who responded and helped my decision making on saving yet another Stang

Really need to fix the issue of the gas fumes. In regards to the divider, in lieu of buying one, I madea divider out of 1/4" Masonite, painted it flat black, and then installed the insulating pad in between the board and seat.

http://www.ebay.com/itm/69-70-Mustang-Mach-Shelby-Boss-Clock-Dash-Woodgrain-OEM-/182225867726?hash=item2a6d8213ce:g:Rz0AAOSwqfNXnawP&vxp=mtr Here's your clock for 99.00

Shocking that 23 post later its an electrical issue

Hey Man, next time take the pizza stone out of the oven before baking