prayers1 153 Report post Posted April 23, 2015 A year ago I replaced the entire front suspension and braking system as well as installing new coil springs. Now I have to replace the coils springs because I was given the wrong ones. It was easier when the rotors were off and I don't recall if anything else was off when I installed the coil springs. Question is, what do I HAVE to take off besides the shock covers and shocks to R&R the coil springs. Thank you! Quote Share this post Link to post Share on other sites
LoneWolf2U 136 Report post Posted April 23, 2015 No, use a internal spring compressor and watch your fingers. Quote Share this post Link to post Share on other sites
fordguy69 24 Report post Posted April 23, 2015 remove sway bar end links, it allows the bottom arm to drop lower. Quote Share this post Link to post Share on other sites
Brian Conway 264 Report post Posted April 23, 2015 You will get assorted methods and options on ' the how to ' but if you just want to do it; put the front end on jack stands, remove the front tires/wheels, remove the front shocks, get a spring compressor and remove the springs. Install new springs and reverse the order to re-assemble. Brian Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted April 23, 2015 Use an internal coil spring compressor. Go through the shock opening at the top of the shock tower. Be careful and don't use an impact gun on the jack screw of the compressor. The pounding from the impact gun will slowly ruin the threads on the compressor. That applies to any type of bearing or hub puller as well. Also, anti seize compound on the screw threads of the compressor help preserve the threads. Sometimes, with strong aftermarket springs, they are short enough to not need a spring compressor. A little pushing and they go into place. Quote Share this post Link to post Share on other sites
prayers1 153 Report post Posted April 23, 2015 Yes good ideals everyone. I was thinking that I would have to drop the lower control arm and the strut rod, then pull one side of the spindle out. From what I gathered, have a jack under the lower control arm, take off sway bar link, shock, shock cover, install compressor, compress spring, lower jack to slide spring out. What do you think! Quote Share this post Link to post Share on other sites
Grabber70Mach 107 Report post Posted April 23, 2015 I think the picture of the external spring compressors that are usually used on struts is an accident waiting to happen. Please use the proper internal spring compressor. Your steps are the way I go about it, but it might help if you take the tire off first. Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted April 23, 2015 Yes good ideals everyone. I was thinking that I would have to drop the lower control arm and the strut rod, then pull one side of the spindle out. From what I gathered, have a jack under the lower control arm, take off sway bar link, shock, shock cover, install compressor, compress spring, lower jack to slide spring out. What do you think! if you have someone press down on the suspension while you compress the spring, you will not have to compress it as much. Quote Share this post Link to post Share on other sites
Ridge Runner 1,113 Report post Posted April 24, 2015 I agree an internal spring compressor is the safest ,it is only one screw through the middle to compress and release the spring .You go through the hole in the top of the tower for the shocks .Any spring compressor can fail so be very careful and make sure it is hooked completely before you tighten the compressor . Quote Share this post Link to post Share on other sites
prayers1 153 Report post Posted April 24, 2015 I will use what I used last, the internal spring compressor that I rented from O'Reillys. Sorry if I misled you all thinking that I'm gonna used the external one. Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted April 24, 2015 I will use what I used last, the internal spring compressor that I rented from O'Reillys. Sorry if I misled you all thinking that I'm gonna used the external one. you didn't mislead anyone . you never said what type you would use. Quote Share this post Link to post Share on other sites
Max Power 74 Report post Posted April 24, 2015 Not only are internal compressers safer, with the close proxinity of the springs to the shock tower walls, they are actually a lot easier to use. I have always liked the type with two hooks at the bottom and the top is actually a plate, but they are hard tofind and arguably only make sense if you are removing the control arm. Quote Share this post Link to post Share on other sites
Brian Conway 264 Report post Posted April 24, 2015 [quote name="prayers1" From what I gathered, have a jack under the lower control arm, take off sway bar link, shock, shock cover, install compressor, compress spring, lower jack to slide spring out. So I gotta ask; why do you think you have to ' take off shock cover ' ? Brian Quote Share this post Link to post Share on other sites
prayers1 153 Report post Posted April 24, 2015 The spring will not come out with the shock cover on. When I installed the 1st set I rented the internal spring compressor with the fork plate. A lot of you guys refer to the finger internal compressor. Which do you all prefer? Here's what my set up looked like after the 1st install. It was easier to put it in all together new and w/o the strut rod and sway bar hooked up, then I tighten all the bolts after the springs were in. Should I remove the strut bar? So just to confirm, I do not need to take off the upper or lower ball joint or spindle. The below attachment is not mine! Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted April 24, 2015 You do not have to remove the upper or lower ball joint or spindle. Simply, 1) Remove the shock and upper shock bracket to expose the opening at the top of the shock tower. 2) Remove the outer spring cover you mentioned. 3) Remove the sway bar end link on the side you are working on. 4) Let the suspension hang. 5) Work the spring compressor through the opening at the top of the shock tower so you can get to the head of the jack screw from the top. 6) Carefully compress the spring enough to remove it. Installation is reverse. When installing it helps to secure the upper spring insulator to the spring with some electrical tape. Then leave the tape in place. I try to move with a purpose when the springs are in a compressed state with the spring compressor. I'm always a little nervous of one letting go. Either of those internal spring compressors you show should work. I've always used the 4-finger type on these classic Mustangs. The 4-finger type is less expensive to purchase which may be why it is more popular. AGAIN, THAT IS NOT MY THUMBNAIL BELOW! Quote Share this post Link to post Share on other sites
Opentracker 4 Report post Posted April 24, 2015 I have the 4 finger compressor. I cut the threaded rod a little shorter so it's easier to use. The issue with getting the spring out and in is to have the suspension relaxed enough so the upper arm is resting on the frame. If the upper arm isn't dropped all the way, the spring is harder to remove / install. Nice looking suspension ! Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted April 24, 2015 . internal types are the best . . the first one you posted is ok . . here are some others. this is the one i use. factory mercedes compressor. . . . Quote Share this post Link to post Share on other sites
Ridge Runner 1,113 Report post Posted April 24, 2015 This is the one i have and prefer ,once it is seated and tightened i think it is the safest . I actually made mine from a heavy duty screw jack Quote Share this post Link to post Share on other sites
prayers1 153 Report post Posted April 24, 2015 1969_Mach1 - Thank you for the confirmation. I always get mixed up with GM and Ford coil spring set ups. I have to sit there and look at it for a while. I too, am always a little nervous of one letting go. Opentracker (John) - I bought your UCA and Spring Perch from you last year. Quote Share this post Link to post Share on other sites
prayers1 153 Report post Posted April 25, 2015 Now I remember why it was easier the 1st time, from looking at my above picture the motor and trans were out. I guess I had a senior moment!!!! Quote Share this post Link to post Share on other sites
fvike 173 Report post Posted April 25, 2015 factory mercedes compressor. . . . This one is the best there is. But do not use power tools on it. Quote Share this post Link to post Share on other sites