69Stanger408 82 Report post Posted June 22, 2017 What did I do wrong? I cant seem to get the pedal assembly to fit with column or vice versa. Even tried with original column (I have the ididit, both have 2" shaft) no luck. Seems like I have something wrong but the holes to the firewall appear to line up (have the master cylinder connected. Assistance (and pics) would help tremendously, the shop manual doesn't lend much assistance and this crap was taken out 10 years ago. 1 Agata@def reacted to this Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted June 22, 2017 I wish I had a three pedal car so I could help. Quote Share this post Link to post Share on other sites
RogerC 136 Report post Posted June 22, 2017 Is your brake pedal in the holes closest to the firewall? That's where power brake pedals mount. Manual or auto trans? Pedal in your first pic is an auto trans power brake pedal. My manual trans manual brakes set up. Rusty set up is 70 manual trans power brakes. Quote Share this post Link to post Share on other sites
69Stanger408 82 Report post Posted June 23, 2017 16 minutes ago, RogerC said: Is your brake pedal in the holes closest to the firewall? That's where power brake pedals mount. Manual or auto trans? Pedal in your first pic is an auto trans power brake pedal. My manual trans manual brakes set up. Rusty set up is 70 manual trans power brakes. Converting from an automatic to a manual and power to non-power due to low vacuum (large cam). I got the clutch pedal from Modern Drive Line, came with new bushings and bolt. I know I need to trim the brake pedal but I can't get it to install w/column. It sits on the same bolt as the clutch does correct. The last pic of yours looks like it does not? Quote Share this post Link to post Share on other sites
RogerC 136 Report post Posted June 23, 2017 There are 4 brake pedals; manual trans manual brakes (my first pic), manual trans power brakes (second pic), auto trans manual brakes, and auto trans power brakes. The manual brake pedals mount on the clutch pedal shaft. The power brake pedals mount with a bolt thru the pivot end of the pedal and high up on the bracket, they're longer. Sounds like you need the same one I have (top pic). 1 Svetlana@Mut reacted to this Quote Share this post Link to post Share on other sites
69Stanger408 82 Report post Posted June 23, 2017 Took it all brake pedal out, here is what I got. As you can see right off the bat, the brake hangs much lower than the clutch. Was on the understanding the pedals are interchangeable (power/nonpower & man/auto). The brake pedal is the original which is for power w/auto trans. Now going to manual brakes with manual trans. Sounds like I need to mount the brake pedal in the upper hole, closet to the firewall? Assume there is a bushing or something for this? Quote Share this post Link to post Share on other sites
RogerC 136 Report post Posted June 23, 2017 48 minutes ago, 69Stanger408 said: Took it all brake pedal out, here is what I got. As you can see right off the bat, the brake hangs much lower than the clutch. Was on the understanding the pedals are interchangeable (power/nonpower & man/auto). The brake pedal is the original which is for power w/auto trans. Now going to manual brakes with manual trans. Sounds like I need to mount the brake pedal in the upper hole, closet to the firewall? Assume there is a bushing or something for this? No, you need the shorter manual brakes pedal. The pedal you have should be mounted in the upper holes but it will not work with manual brakes. There is a different working ratio between the manual pedals and the power pedals. The manual pedals provide more mechanical advantage over power brake pedals to reduce pedal effort. Quote Share this post Link to post Share on other sites
Rsanter 152 Report post Posted June 23, 2017 You need a manual pedal, what you have is a power pedal and it is mounted in the wrong place bob Quote Share this post Link to post Share on other sites