Footcutter11 23 Report post Posted May 21, 2015 I may need to steel your idea for the front spoiler.... I need to come up with a side air dam idea to cover the exhaust. Any thoughts? Quote Share this post Link to post Share on other sites
Rip Rock 13 Report post Posted May 22, 2015 She looks badass! I love the color. I am limiting mine to 20PSI as well. I have a 9:1 Comp ratio and 91 Octane with a touch of methanol, and some E3s. May think about a wet meth system at some point. Do you know what comp ratio you are using? I am also running a T5 tranny and an 8 inch trac lok rear, so one of those two will blow first. LOL. You have done some amazing fab work, and I bet when you raise the hood people oooh and ahhh! What boost do you see with no load? The Holley HP is the perfect EFI for dummies (me), as well as, more advanced users which I like. Again, sweet ride you got there! The comp is 8.4:1 in this engine. I'm not sure what you mean with , boost with no load, I haven't set up the 2 step yet too see what this car likes on the dig. There is also a methanol system in here as well. I haven't had it tuned with it yet, but it's in there. I might get it tuned with it as well, a second tune. So I'm looking into an e dash for the xfi ecu , to select between tunes without caring a lob top. Thanks for the compliment!! Quote Share this post Link to post Share on other sites
Footcutter11 23 Report post Posted May 22, 2015 No load, means reving the engine in neutral. I was just curious... Quote Share this post Link to post Share on other sites
Rip Rock 13 Report post Posted May 29, 2015 No load, means reving the engine in neutral. I was just curious... Sorry I took so long. Kind of forgot about this. With no load I have no boost. My buddy however.. He has a turbo'd 51 Chevy truck and he has 1-2 psi at idle.lol Quote Share this post Link to post Share on other sites
Rip Rock 13 Report post Posted May 29, 2015 Here's a picture from the rear.Finally got the car out in some sunlight. Not much for a sunny day, but know the car knows what the day looks like. Quote Share this post Link to post Share on other sites
Footcutter11 23 Report post Posted June 1, 2015 Sorry I took so long. Kind of forgot about this. With no load I have no boost. My buddy however.. He has a turbo'd 51 Chevy truck and he has 1-2 psi at idle.lol Good conformation on what I see. Thanks! Quote Share this post Link to post Share on other sites
Footcutter11 23 Report post Posted June 1, 2015 Damn, that thing is beautiful! I like the blacked out chrome bits. Exactly what I was thinking, very inspiring build! Quote Share this post Link to post Share on other sites
Rip Rock 13 Report post Posted June 1, 2015 Thanks! Hopefully I'll have it back on the rollers this month or next. Then I can start to drive it again. Put this car on hold for a bit so I can finish up the other car, which is going on the rollers today for a pump gas tune. 1 Footcutter11 reacted to this Quote Share this post Link to post Share on other sites
Footcutter11 23 Report post Posted June 1, 2015 Thanks! Hopefully I'll have it back on the rollers this month or next. Then I can start to drive it again. Put this car on hold for a bit so I can finish up the other car, which is going on the rollers today for a pump gas tune. Can't wait to hear the numbers. Quote Share this post Link to post Share on other sites
Rip Rock 13 Report post Posted June 3, 2015 Will be on hold for a bit longer. Had worst case on the Dyno with the supra. Compression on cylinder one is 0. Ugg. Hopefully I can get this done in a timely fashion so I can get back on the mustang. Quote Share this post Link to post Share on other sites
Footcutter11 23 Report post Posted June 3, 2015 Will be on hold for a bit longer. Had worst case on the Dyno with the supra. Compression on cylinder one is 0. Ugg. Hopefully I can get this done in a timely fashion so I can get back on the mustang. Blah! I hope it is something easy... Quote Share this post Link to post Share on other sites
Rip Rock 13 Report post Posted June 3, 2015 Blah! I hope it is something easy... took a scope to see in each hole. Looks like the piston. Melted on the edge. Quote Share this post Link to post Share on other sites
Footcutter11 23 Report post Posted June 3, 2015 took a scope to see in each hole. Looks like the piston. Melted on the edge Oh, that's no bueno... Quote Share this post Link to post Share on other sites