Rudolph Schenker 14 Report post Posted December 3, 2010 Couple more pics............... Quote Share this post Link to post Share on other sites
468stang 11 Report post Posted December 3, 2010 Man that front-end looks sweet, are you using your column or the TCI steering column? Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted December 3, 2010 (edited) Man that front-end looks sweet, are you using your column or the TCI steering column? Ididit column, most likely. The stock column is a little too "worn". :001_smile: Edited December 3, 2010 by Rudolph Schenker Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted December 6, 2010 Test fitting........ Quote Share this post Link to post Share on other sites
Dro69 11 Report post Posted December 6, 2010 i wish i had the cash and knowledge of swapping in a 4.6dohc supercharged engine in my stang. Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted December 7, 2010 i wish i had the cash and knowledge of swapping in a 4.6dohc supercharged engine in my stang. I don't know about "knowledge", I'm getting "some" help :wink:. It is slowly coming along. Quote Share this post Link to post Share on other sites
MikeStang 247 Report post Posted December 8, 2010 You have to chop the snot out of the tranny tunnell:? If you get on youtube and look up project Dark horse, they have a 69 or 70 they have installed the same combo as you are working on... Mike Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted December 8, 2010 You have to chop the snot out of the tranny tunnell:?If you get on youtube and look up project Dark horse, they have a 69 or 70 they have installed the same combo as you are working on... Mike Great thanks for the link!!!:thumbup1: Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted December 21, 2010 Slow progress, few more pics............ Looks like I'll need to run lines to a remote oil filter............. I'm going to need to notch the trans tunnel a bit to get the upper bolts in........ I have to reroute the AC lines as they come too close to the passenger head........... So I have a bit of work ahead :hammer: Quote Share this post Link to post Share on other sites
468stang 11 Report post Posted December 22, 2010 It will all be worth it in the end, what did that motor come out of. Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted December 22, 2010 It will all be worth it in the end, what did that motor come out of. 03 Cobra. Motor has 30k on it. I got the whole drive train, ECM, wire harness, heat exchanger, drive shaft, and exhaust. Quote Share this post Link to post Share on other sites
Hotrodizz 10 Report post Posted January 8, 2011 Looking good. Starting on a 69 5.0 mod-motor project myself here soon. Hope the pictures I sent you a while back helped a little. Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted January 8, 2011 03 Cobra. Motor has 30k on it. I got the whole drive train, ECM, wire harness, heat exchanger, drive shaft, and exhaust. How much did you pay for it if you dont mind me asking? I'm also planning on a 5.4 dohc supercharged swap. Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted January 9, 2011 How much did you pay for it if you dont mind me asking? I'm also planning on a 5.4 dohc supercharged swap. PM sent. Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted January 9, 2011 Looking good. Starting on a 69 5.0 mod-motor project myself here soon. Hope the pictures I sent you a while back helped a little. They were very helpful! Thanks again! Quote Share this post Link to post Share on other sites
69351mach 10 Report post Posted January 10, 2011 Man that is going to be a sweet car when it's done!:thumbup1: Quote Share this post Link to post Share on other sites
468stang 11 Report post Posted February 10, 2011 Anything new with the car? Haven't seen an update in awhile. Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted February 15, 2011 Anything new with the car? Haven't seen an update in awhile. I have been delayed by the rear frame rails. :cursing: I was installing the rear suspension components and decided the rails needed to be replaced! Pics coming soon! :yes::yes: Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted February 16, 2011 Passenger side done............... Working on driver side........... Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted February 19, 2011 More progress.................... Quote Share this post Link to post Share on other sites
unfrozen1969 11 Report post Posted February 19, 2011 Nice progress, thanks for the photos and keep them coming... Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted February 23, 2011 couple more.......... Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted February 28, 2011 1 wheel well done, 1 to go............. Quote Share this post Link to post Share on other sites
Grabber70Mach 107 Report post Posted March 1, 2011 Looking good. How wide is the strip you added to the wheel wells? Did it bring the inner wheel wells even with the frame wells? Quote Share this post Link to post Share on other sites
Rudolph Schenker 14 Report post Posted March 1, 2011 Looking good. How wide is the strip you added to the wheel wells? Did it bring the inner wheel wells even with the frame wells? Adding the additional strip brought the inner fender well almost even to the rear frame rails. Gave me an additional 1 1/2 inches. Hopefully this will allow wider tires. Quote Share this post Link to post Share on other sites
