JET 445
-
Content Count
201 -
Joined
-
Last visited
-
Days Won
4
Posts posted by JET 445
-
-
I laid my harness out on the floor, connected the earths to a piece of steel tubing and then tested and repaired all the circuits, then wrapped it and installed it in the car.
Grabber70Mach reacted to this -
Wow, nice car, I don't know what it's worth but if it was mine I would put on red Mach 1 stripes and get rid of the black wheels.
-
-
I live in Australia and I used a local Mustang importer to find a car and import it for me, I told him I wanted an old faded unmolested car, I did'nt care about the mechanical condition I just wanted a good body and that is what he got for me. When I first looked at it I saw some rust in one floor pan and some around the gas tank and I was a little disappointed but I soon realised how good it was and now I am so thankful that I was lucky enough to get one of the best 69 bodies you will ever find.
-
Ash, if you want that timing cover to look like new get it vapour blasted [ wet blasted with tiny glass beads ]. I had my front calipers done they came up fantastic, I think it would look great if you left it bare- a nice contrast against the black engine.
-
I find the squeak is nearly always caused by the spring saddle bushes, squirt a bit of lube into the bushes and see if the noise goes away.
-
-
If you have not welded the top of the cowl yet it is a good idea to glue a piece of stainless steel mesh over the air intake of your air conditioning, this will keep rubbish out of the fan and also keep mice out of the car, those little critters love to get in and chew up your interior.
-
Make sure you fit the grill surround and the moulding to the headlight bucket before you fit the bucket to the fender
-
-
I used a hole saw to cut the four corners so that I would have a nice smooth radius in the corners and then cut the edges with an angle grinder fitted with a 1mm thick cutting disc, worked great, give the edges a quick file and it turned out perfect.
-
If you have reproduction handles they could be the problem, the ones I bought were rubbish, they would not fit through the hole in the doorskin and I had to fit all the original internal linkages to the new handles, if I were to do it again I would rechrome the original handles.
-
Joins are done here behind plastic caps
-
I don't think you understand what I mean, look down at the top of the dash, look at the radius of the curves where the cluster mounts on top of the lower dash, they are completely different, this is why most people including me cut the dash behind the 4 plastic caps and swap each side in one complete piece. This will mean your air-con vents are in the center of the car but you will be sure of the clusters fitting because they will be going back in their original openings.
-
You may want to double check before you go cutting that dash there, the problem is the inner and outer curves are different, look at the curve above the air vent and look at the curve near the radio-see the difference?. When you swap the cluster and clock over they probably won't fit the curves.
-
I had the same problem with my new engine, it felt fine turning it over by hand but when it was running there was a ticking under the valve cover, turned out one of the rocker arms was just touching the baffle under the filler cap, a light tap with a hammer and the problem was gone. Yours is probably the same,undo your valve cover bolts and with the engine running lift the valve cover slightly, if the noise stops you have found your problem.
-
Interesting to note that the car in your first pic only has the tab on one fender, my very early build 69 has no tabs on either side.
-
Just look on Australian ebay or search for Australian XY GT shaker, full metal shaker top to bottom about $700 US.
Mach 1 resto in Australia
in Project Progress Forum
Posted · Report reply
There should be slots in the rear seat base for the seat belts to come up through, this will make them go across your hips not around your waist.