68stang289 26 Report post Posted January 20, 2014 (edited) Looking to clear out some parts from the garage that I have been moving around for far too long now. All prices are OBO + the ride (or local pick-up in Southwest Florida), or trade for a set of 1" lowering springs and/or a driver/decent quality 70+ rimblow steering wheel. Pictures are available upon request. 69 Interior Quarter Trim Caps (pair) - $5 Fills the gap between the rear interior quarter panel and the sail panel in the corner where the pinch on windlace ends. Average condition original part. FE Accel Distributor - Offer? Came off of my 428 when I went with a new setup and has a new gear on it. Bearings and gear are new. Includes cap and rotor. Has some black paint up the side and could use a good cleaning. Dual points with no vacuum advance and a tach drive setup. 60-63 352 FE Distributor - $5 Single points distributor with vacuum advance. Could use a rebuild. No cap or rotor. Was told it was 390/428 when I picked it up, but the C0AF12127D (1FB) number says otherwise. NOS C90B12250A Wiring Harness - Offer? New with Ford tag still attached. Master Parts Catalog says it is the pink resistor wire used for the coil. 67/68 289/302 Pressure Side Power Steering Hose - $25 Brand new, never used. Pressure side hose from the pump to the control valve. I ended up using the P/S setup on my 70 and this hose will not work for what I need. 67-70 Pitman Arm - $15 Has been media blasted and primered. For manual steering cars. I believe it is a 1 1/8" diameter sector shaft fitment. Great shape, but I swapped over to PS. 69/70 302/351? Power Steering Bracket - $5 I believe this is correct for a 69/70 302/351 (I couldn't find any part numbers on it though). It's in good shape but it could use a decent cleaning and some paint. Small Block (302/351)? Power Steering Pulley - $5 Not entirely sure what this is correct for as I could not find a part number anywhere on it. It measures approximately 6 1/4" across and has a sheeve width of approximately 5/8" from inside lip to inside lip. I was told it came off of a small block 69 Cougar when I picked this part up. Please someone chime in if this is incorrect as I do not want to misadvertise it. 70+ Rimblow Steering wheel and pad - $125 Needs restoration. Pad was repainted black from green at some point and the paint is starting to flake off in places. Missing the 3 inserts, but has the center running pony insert. Wheel itself has the usual cracks. I was going to have it restored, but I decided to put the money elsewhere and just look for a decent driver quality wheel instead. Edited April 5, 2014 by 68stang289 Quote Share this post Link to post Share on other sites
J's69Mach1 17 Report post Posted January 20, 2014 Pm sent on moroso coolant catch can and idler arm. Quote Share this post Link to post Share on other sites
390mach1 49 Report post Posted January 20, 2014 Pm sent on rim blow. Quote Share this post Link to post Share on other sites
68stang289 26 Report post Posted January 21, 2014 PM's replied to. Quote Share this post Link to post Share on other sites
Zipppo 11 Report post Posted January 21, 2014 I am interested in the 1967 Mustang Idler arm. My car is a 67 Couple 6 cylinder 200cid with Manula steering. Also if it firs what is shipping to Redondo Beach Ca. 90277 Thank you Quote Share this post Link to post Share on other sites
jholmes217 65 Report post Posted January 22, 2014 Interested in the FE Accel Distributor. What is the part or model number? Quote Share this post Link to post Share on other sites
68stang289 26 Report post Posted January 22, 2014 I am interested in the 1967 Mustang Idler arm. My car is a 67 Couple 6 cylinder 200cid with Manula steering. Also if it firs what is shipping to Redondo Beach Ca. 90277 Thank you There's a few people ahead of you for the idler arm. If those fall through, I will keep you posted. Interested in the FE Accel Distributor. What is the part or model number? The sticker that was on it is long gone. The part number looks like I48705 or I48765. I couldn't find anything on either of those numbers with a Google search though. Quote Share this post Link to post Share on other sites
jholmes217 65 Report post Posted January 22, 2014 Is the Accel distributor a dual point or electronic? Does it have have vacuum advance? Quote Share this post Link to post Share on other sites
68stang289 26 Report post Posted January 24, 2014 Is the Accel distributor a dual point or electronic? Does it have have vacuum advance? It is a dual points setup with no vacuum advance and a mechanical tach drive. It has access holes on both sides so you can adjust the points without removing the cap and rotor. Quote Share this post Link to post Share on other sites
68stang289 26 Report post Posted January 24, 2014 Brake pedal pad, idler arm and catch can all sold! Quote Share this post Link to post Share on other sites
jholmes217 65 Report post Posted January 24, 2014 It is a dual points setup with no vacuum advance and a mechanical tach drive. It has access holes on both sides so you can adjust the points without removing the cap and rotor. Thanks for the clarification. I'm looking for an electronic with vacuum advance, so I'll pass. Thanks. Quote Share this post Link to post Share on other sites
fordbsg 10 Report post Posted February 4, 2014 I need the seat stops. Quote Share this post Link to post Share on other sites
68stang289 26 Report post Posted February 5, 2014 I need the seat stops. Shoot me a PM with your address. Quote Share this post Link to post Share on other sites
68stang289 26 Report post Posted March 17, 2014 List and some prices updated! Quote Share this post Link to post Share on other sites
