StephenC 10 Report post Posted March 15, 2011 So I'm getting ready to prime my car here in the next week once it warms up alittle more and I have all the supplys needed to do it myself. So I'm curious to see if anyone else has built a spray booth in there garage if so how? And how did it turn out? Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 15, 2011 So I'm getting ready to prime my car here in the next week once it warms up alittle more and I have all the supplys needed to do it myself. So I'm curious to see if anyone else has built a spray booth in there garage if so how? And how did it turn out? Quote Share this post Link to post Share on other sites
unfrozen1969 11 Report post Posted March 16, 2011 I did mine by hanging plastic from the walls and roof, taping the seams and putting water on the floor when I sprayed, that way the paint would not stain the cement and washed away. Quote Share this post Link to post Share on other sites
unfrozen1969 11 Report post Posted March 16, 2011 I did mine by hanging plastic from the walls and roof, taping the seams and putting water on the floor when I sprayed, that way the paint would not stain the cement and washed away. Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 17, 2011 Thats bassicly what I'm doing im building a skelton out of some 2x4 and hanging the plastic off that and putting a tarp on the ground. What did you use as ventalation? I was going to use about 2 or 3 box fans with heater filters on both sides to keep the fumes down and get a good negative pressure inside the "booth" how did yours turn out? Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 17, 2011 Thats bassicly what I'm doing im building a skelton out of some 2x4 and hanging the plastic off that and putting a tarp on the ground. What did you use as ventalation? I was going to use about 2 or 3 box fans with heater filters on both sides to keep the fumes down and get a good negative pressure inside the "booth" how did yours turn out? Quote Share this post Link to post Share on other sites
MikeStang 247 Report post Posted March 17, 2011 Hang the plastic as mentioned above, and then cut a hole in the front and tape an air filter from your house ac on over the hole.... Use one of the good filters, not that cheep ass blue one.....then cut another hole at the other end and install a box fan so that its blowing out of the booth....this will help provide positive ventilation, and suck the fumes out......I saw one a fellow hqd built similar to this but he frame-up a little room out of 2x4's so he could staple the plastic to it and installed one of those big attic fans......I got to see some of his work, and couldn't believe how nice and clean it was?..I was amazed that kind of work could be done in those conditions. Mike Quote Share this post Link to post Share on other sites
MikeStang 247 Report post Posted March 17, 2011 Hang the plastic as mentioned above, and then cut a hole in the front and tape an air filter from your house ac on over the hole.... Use one of the good filters, not that cheep ass blue one.....then cut another hole at the other end and install a box fan so that its blowing out of the booth....this will help provide positive ventilation, and suck the fumes out......I saw one a fellow hqd built similar to this but he frame-up a little room out of 2x4's so he could staple the plastic to it and installed one of those big attic fans......I got to see some of his work, and couldn't believe how nice and clean it was?..I was amazed that kind of work could be done in those conditions. Mike Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 17, 2011 Thanks Mike I'll be taking a trip up to home depot tommarow and get some filters. I never thought of an attic fan though that would ideal for the way my garage is set up. I'm just worried about all the dust and debris getting on my car while I'm paint so I have to really clean everything this weekend and get some good filters. The booth I'm setting up is 20'x14'x8' so I'm trying to think about how many fans I might need. Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 17, 2011 Thanks Mike I'll be taking a trip up to home depot tommarow and get some filters. I never thought of an attic fan though that would ideal for the way my garage is set up. I'm just worried about all the dust and debris getting on my car while I'm paint so I have to really clean everything this weekend and get some good filters. The booth I'm setting up is 20'x14'x8' so I'm trying to think about how many fans I might need. Quote Share this post Link to post Share on other sites
Legion 10 Report post Posted March 17, 2011 Here's a pic of one built using 2" pvc and plastic. He said he had less than $300 bucks in it, including the lights. I've also read that you want to place the fans and filters pushing air into the 'booth' and an evacuation hole on the other end, creating positive pressure in the booth. Supposedly it's better for the homemade paint booths to keep bugs and airborne particles out...versus pulling air into the booth through small gaps or holes. It also keeps the overspray from running across the box fan motor. I don't think they cause sparks like the old DC brush motors did, but better safe than sorry. I personally like this one.... Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 17, 2011 Legion if I had the money that retactable one would be awesome to get you could fit like 10 cars in that thing at a time! Quote Share this post Link to post Share on other sites
Pakrat 1,043 Report post Posted March 17, 2011 I know I have heard in the past that a good reason to keep the floor wet as opposed to a tarp is not only to keep it clean but to keep the dust and dirt down, it can't blow up off the floor or be lifted while you move when it is trapped in the water. Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 17, 2011 I know I have heard in the past that a good reason to keep the floor wet as opposed to a tarp is not only to keep it clean but to keep the dust and dirt down, it can't blow up off the floor or be lifted while you move when it is trapped in the water. Ive heard that also about keeping dust down. But I was just going to put down a tap on the floor so it doesnt get paitned do you think I shoud wet the floor instead or lay down a tarp and wet that? I got the fram build today and will get my plastic Saturday with the filters so I will be paint Monday mre than hopefully. Quote Share this post Link to post Share on other sites
Legion 10 Report post Posted March 18, 2011 (edited) A friend of mine is a painter and they wet the floor in their booth since they don't have a down draft setup. I take it you plan on sealing the pastic to the tarp, so wetting down the inside would give you some added insurance. Edited March 18, 2011 by Legion Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 18, 2011 A friend of mine is a painter and they wet the floor in their booth since they dont' have a down draft setup. I take it you plan on sealing the pastic to the tarp, so wetting down the inside would give you some added insurance. Thanks I'll do that, I just want to get this done right the first time. Quote Share this post Link to post Share on other sites
Pakrat 1,043 Report post Posted March 18, 2011 I think no matter what their will always be some junk that gets in and needs to be sanded out and in my opinion sanding is the least desirable part of the painting process so I think any little steps that you can do to reduce that process and eliminate even just one extra round with a heavier grit is well worth it. Quote Share this post Link to post Share on other sites
unfrozen1969 11 Report post Posted March 18, 2011 Wetting down the floor helps with overspray as well, the paint tends to just sit on top, and does not cure, unless the water evaporates, I was able to squeegy mine out gentle after the paint had set. Take some photos so we can see what you ended up building Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 18, 2011 Wetting down the floor helps with overspray as well, the paint tends to just sit on top, and does not cure, unless the water evaporates, I was able to squeegy mine out gentle after the paint had set. Take some photos so we can see what you ended up building I'll take some pics as soon as possible. Question about sanding though do you reccomend wet sanding or dry sanding? Ive heard mixed reveiws on both and I have personally only wet sanded. Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 21, 2011 Heres all I got done so far build the frame today and put up to walls with 7mil plastic still have to do the back and front and figure were I'm going to put the door to get in and out of the booth. Quote Share this post Link to post Share on other sites
jgstang 21 Report post Posted March 28, 2011 here is i did, just built 2x4 walls and through up some drywall and my wife painted it...used ac filters with some cheap doors and away i go...oh you need a spark proof exhaust fan! Quote Share this post Link to post Share on other sites
69RavenConv 286 Report post Posted March 28, 2011 As someone else who is going to attempt a homemade paint booth, I appreciate this thread. On a related note, does anybody have any ideas on cheap stands for the fenders, hood, etc? PVC, 2x4's, something else? Yours look great, jgstang, but probably more than I want to spend? Quote Share this post Link to post Share on other sites
StephenC 10 Report post Posted March 28, 2011 As someone else who is going to attempt a homemade paint booth, I appreciate this thread. On a related note, does anybody have any ideas on cheap stands for the fenders, hood, etc? PVC, 2x4's, something else? Yours look great, jgstang, but probably more than I want to spend? I bought 2 stands from eastwood fairly cheap I believe just going to paint on those. And yeah jgstang you got a really nice setup there I was going for cheap if it was going to be permanent and I was restoring multiple cars thats deffinatly what I would do. Those stands though are $30 a peice I had a coupon code when I bought mine so they were cheaper http://www.eastwood.com/500lb-work-stand.html Quote Share this post Link to post Share on other sites
Junior2561 10 Report post Posted March 28, 2011 As someone else who is going to attempt a homemade paint booth, I appreciate this thread. On a related note, does anybody have any ideas on cheap stands for the fenders, hood, etc? PVC, 2x4's, something else? Yours look great, jgstang, but probably more than I want to spend? off topic, but where are in NE Ohio are you? I'm near wooster. Quote Share this post Link to post Share on other sites
69RavenConv 286 Report post Posted March 29, 2011 Those stands look sweet and the price is right. Thanks Stephen. Junior, I'm in Richfield Twp. There's a few Buckeyes here. Quote Share this post Link to post Share on other sites