LOTS of parts for sale.

[fordguy69 24]

Need room in my garage sale:

 

Koni SP-1 drag shocks front and rear 67-70 Mustang/Cougar barely used 150.00 fits stock front and rear suspension.

 

Competition Engineering housing floaters with bottom plate for Ford shocks used 60.00 Fits up to 3” axle tubes and stock width Mustang leafs.

 

Chassis Engineering double adjustable ladder bars used 125.00

 

1969/70 Mustang bolt on/weld on subframe connectors. used 75.00

 

Rear leaf springs, 69-70 Mustang, 428 CJ spec springs, stock ride height. Barely used 100.00

 

1969 –70 Coupe fiberglass deck lid, pin on. Stock style, no duck tail, fits stock quarter extensions. new 150.00

 

1969 Mustang 428CJ front coils new w/one full coil removed. 40.00

 

1969 Mustang 428CJ front coils used 40.00

 

9” third member used , 4.33 gears, 28 spline Detroit Locker, standard single rib case. 400.00

 

Crane Mechanical Flat Tappet 289-302-351W used .525”I/.549”E 280/290 Adv. Duration 242/252 Duration @.050 108 Centerline. 60.00

 

Crower Mechanical Flat Tappet 289-302-351W used .622”I/.629”E 310/316 Adv. Duration 276/278 Duration @.050 108 Centerline. 60.00

 

Crane Hydraulic Flat Tappet HIT 292-2-NC 289-302-351W new .544”I/.546”E 292/302 Adv. Duration 110 Centerline. 100.00

 

Crane Mechanical Flat Tappet 429/460 used .583”I/.603”E 292/302 Adv. Duration 256/266 Duration @.050 108 Centerline. 125.00

 

Edelbrock 1725 new in box. 289-302-351w mechanical fuel pump. 70.00

 

Mallory 3755101 Unilite distributor used 289/302 150.00

 

2 sets Crites Gen 1 frame mounts and engine mounts for 67-70 Mustang/Cougar with 429/460. New set 100.00 Used set 75.00

 

Weld Drag Lights Rear 15x8 drilled for screws. 3.5bs used 225.00/pr

 

Moroso electric water pump drive motors, one new 55.00 w/new belt, one used 25.00

 

Electronics setup for bracket racing, used. MSD 6 #6400, MSD Softouch Rev Control #8738, MSD Two Step #8739, MSD RPM activated switch #8950, RPM module selector #8672, Autometer Pro Light #3240, Line Master single delay box. Set up to activate low rpm limiter when transbrake or line locks are activated, high side of two step for upper rpm limit, rpm activated switch utilizes the module selector to activate shift light/shift solenoid. Delay box holds transbrake or line locks for set delay time and holds low rpm limit of two step. Over 500.00 worth of electronics. 200.00

 

All prices DO NOT include shipping. I am in west central Florida 34602. email me at cattledogranch@bellsouth.net for more info or pictures.

 

Thanks, Bill.

Edited October 17, 2013 by fordguy69
removed sold items

[shelbyshelby 52]

Do you know the duration @.050 on the HIT 292-2-NC cam for the 289-302-351?

[fordguy69 24]

Do you know the duration @.050 on the HIT 292-2-NC cam for the 289-302-351?

 

Unfortunately I don't. Can't find the cam card and all the old pre-bankruptcy Crane catalogs and info seem to be scrubbed from the net. I thought nothing ever left the net???

 

The only info I could find was for an HIT -280, but extrapolating from those numbers, I would guess the .050 numbers for this one to be 236I, 246E.

 

IIRC, we bought this cam for a 65 mustang with a 289 with 10.5 cr and ported Windsor heads with a Doug Nash 5-speed. I think it was the second biggest hydraulic cam they had for this motor at the time. Brother in law wrecked and sold the car before we changed the cam.

[miketyler 15]

If you email them they will send you the spec card. I had same questions on my cam when I couldn't find it on their website. Unless it was a custom grind they probably have an identical model with newer PN.

[fordguy69 24]

If you email them they will send you the spec card. I had same questions on my cam when I couldn't find it on their website. Unless it was a custom grind they probably have an identical model with newer PN.

 

Thanks for the suggestion Mike. Got a cam card from them today. And I guessed right. Duration at .050 is 236I 246E.

[juit 34]

best price on the subframe conectors shipped to rio grande city texas

[fordguy69 24]

pm sent