-
Content Count
498 -
Joined
-
Last visited
Posts posted by Boogerschnot
-
-
Do you remember what size u joint you had to order to fit the old driveshaft to the newer yoke?? Im trying to get the right one.
-
I found that the new chrome pieces were too long so I had to smash little "fingered washer" things like a rivet onto the posts, then use my dremel tool and a cutoff wheel and grind the posts down so they would allow the scoop to fit the car.
So the answer to your question is, yes, you ground off the stud tabs and everything comes apart. Then you get the new ones with small locking washers that you smash onto the new studs to hold them in place again. Then you grind down the new stud to fit the scoop to your car.
-
Im going to order one pretty soon and when I do I will put up lots of pictures. It seems like no one has ordered these things so far. There is an article by mustang monthly where they installed one in an earlier mustang and it looked nice. But they had it sitting too far forward. http://www.mustangandfords.com/techarticles/interior/mufp_0609_tmi_upholstery_interior_restoration/index.html
-
Use some window weld to glue it into place. There is a mustang monthly article somewhere out there that tells you how to do it. I paid some guys to put a new one in. Usually if you order a windshield they will install it. Maybe you could even have them remove the old one and install it into your car.
-
Is there a way to tell what carrier bearing I need without pulling it from the rear end. I really want to get this stuff ordered and still drive the car while I wait. Its my daily driver.
-
Is there a way to tell what carrier bearing I need without pulling it from the rear end. I really want to get this stuff ordered and still drive the car while I wait. Its my daily driver.
-
I want to order my 4.11's but dont know which bearing kit to buy for the swap. Ive got 28 a spline open rear now in the grande'. Its still original to the car. So what is the best bet on instal kits?
-
I want to order my 4.11's but dont know which bearing kit to buy for the swap. Ive got 28 a spline open rear now in the grande'. Its still original to the car. So what is the best bet on instal kits?
-
Thanks Mike.
-
Thanks Mike.
-
Thanks Mike.
-
I just recieved an entire front end suspension set up from John and I am soo ready for the weekend. I ordered this stuff last Friday from Hawaii, and I got it in today (Tuesday) awsome service!!
-
I just recieved an entire front end suspension set up from John and I am soo ready for the weekend. I ordered this stuff last Friday from Hawaii, and I got it in today (Tuesday) awsome service!!
-
I just recieved an entire front end suspension set up from John and I am soo ready for the weekend. I ordered this stuff last Friday from Hawaii, and I got it in today (Tuesday) awsome service!!
-
Mike. thanks for the reply. I havent installed it yet and Im hunting down all of my parts now. Its a 93 Mustang AOD. the shifter nub points down. Im trying to use my stock throttle cable from the 69. I would love a good write up on any snags you ran into and what you used for your swap. It would help a lot. Plus it would be here for any other AOD guys.
-
Mike. thanks for the reply. I havent installed it yet and Im hunting down all of my parts now. Its a 93 Mustang AOD. the shifter nub points down. Im trying to use my stock throttle cable from the 69. I would love a good write up on any snags you ran into and what you used for your swap. It would help a lot. Plus it would be here for any other AOD guys.
-
Mike. thanks for the reply. I havent installed it yet and Im hunting down all of my parts now. Its a 93 Mustang AOD. the shifter nub points down. Im trying to use my stock throttle cable from the 69. I would love a good write up on any snags you ran into and what you used for your swap. It would help a lot. Plus it would be here for any other AOD guys.
-
Anyone? I would like to oder what I need and am still trying to figure it out.
-
Anyone? I would like to oder what I need and am still trying to figure it out.
-
Anyone? I would like to oder what I need and am still trying to figure it out.
-
Do I have to use a new throttle cable with the TV adapter or can I use the old one? Ive got a holley 670 street avenger.
-
Do I have to use a new throttle cable with the TV adapter or can I use the old one? Ive got a holley 670 street avenger.
-
Do I have to use a new throttle cable with the TV adapter or can I use the old one? Ive got a holley 670 street avenger.
-
Yeah....that?s right FC2 maybe FC1. Well shippy.....it's the absolute least I can do for someone serving this country!!!! If I could do the swap for you I would!Thank you. I did pick up E-6 in December so FC1, you have already pretty much built this thing for me man. I probably would have skipped on the tranny if I had not have found your thread about the install. All of the help I have gotten so far is soooo greatly appreciated!
Torq Thrust 17'' Streeter wheels
in 1969-70 Technical Forum
Posted · Report reply
Ive got 255 45's in the rear and 245 45's up front.. Fit great and the rear is just a tad bit taller/wider, its hardly noticed.