Machspeed 219 Report post Posted December 1, 2019 That jig you built is pretty slick! About how much time does is save you in the alignment of the panels for which it was built for and is it's use limited to the 67 and 68? Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 2, 2019 On 12/1/2019 at 8:24 AM, Machspeed said: That jig you built is pretty slick! About how much time does is save you in the alignment of the panels for which it was built for and is it's use limited to the 67 and 68? It cuts our time in half with no mistakes. We have one for the 65-66 and the 67-68. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 3, 2019 Mini tubs going in , he also wants our roll bar installed Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 3, 2019 I missed these pictures. 2 mikee and Grabber70Mach reacted to this Quote Share this post Link to post Share on other sites
Ridge Runner 1,112 Report post Posted December 3, 2019 I have had to replace a few wheel tubs ,not fun with the quarters still on ,or just doing an inside tub .even had to do one on a finished car when a tire took one out and didnt damage the quarter Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 3, 2019 It twice as fast the way we do it now, since our manufacturer just installs the inner with tubs with a couple of screws. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 6, 2019 Blending is done, ready for some Epoxy primer. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 7, 2019 Mini tubs are done. Once it's in primer and our suspension front and back installed, it goes back to Florida. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 7, 2019 One final test fit of our Shelby nose before we oull it all apart and prime. The gaps are absolutely perfect. 1 Grabber70Mach reacted to this Quote Share this post Link to post Share on other sites
Vicfreg 771 Report post Posted December 9, 2019 Nice Job....! Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 10, 2019 First round of Epoxy primer. 2 mikee and Grabber70Mach reacted to this Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 10, 2019 Blending the right side. Quote Share this post Link to post Share on other sites
Midlife 814 Report post Posted December 11, 2019 What's with the hand marks everywhere? Don't you tell your folks to wash their hands??? Quote Share this post Link to post Share on other sites
Caseyrhe 650 Report post Posted December 11, 2019 Isn't that what its mea 32 minutes ago, Midlife said: What's with the hand marks everywhere? Don't you tell your folks to wash their hands??? Isn' that what it meant by "all hands on deck" 1 mustangstofear reacted to this Quote Share this post Link to post Share on other sites
Ridge Runner 1,112 Report post Posted December 11, 2019 1 hour ago, Midlife said: What's with the hand marks everywhere? Don't you tell your folks to wash their hands??? Some one has never watched a body man in action ,i was once accused of feeling up a mustang ,could be ,but i was checking the surface ...sort of ! Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 11, 2019 2 hours ago, Midlife said: What's with the hand marks everywhere? Don't you tell your folks to wash their hands??? Pretty good eyes for an old guy :) Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 11, 2019 Since our customer is saying he will have between 800-1000 HP, we're adding to our roll bar and attaching it to the framerails Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 11, 2019 Customer wants to keep his rear seat, so the tube needs to be higher to clear the seat. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 13, 2019 Mock up of the PVC is done, now we can start making it out of the tubing. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 14, 2019 Finishing up the backend of the car. Took a lot more work with the Dynacorn decklid :( 1 Grabber70Mach reacted to this Quote Share this post Link to post Share on other sites
newstang 388 Report post Posted December 14, 2019 6 hours ago, mustangstofear said: Finishing up the backend of the car. Took a lot more work with the Dynacorn decklid :( have you tried the new aluminum one? I remember getting an email from dynacorn that is a new item. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 14, 2019 If the aluminum one fits as bad as the steel one, it will only make matters worse unless you're really good at tig welding, which most aren't. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 17, 2019 Last round of Epoxy primer. Quote Share this post Link to post Share on other sites
Alan_Mac 48 Report post Posted December 20, 2019 On 10/24/2019 at 5:38 PM, mustangstofear said: Trump is the man :) Please refrain from politics in this forum. Its should be free from this type of BS. Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted December 20, 2019 5 hours ago, Alan_Mac said: Please refrain from politics in this forum. Its should be free from this type of BS. That would only be if I was talking about Demorats LOL. Quote Share this post Link to post Share on other sites
