1969_Mach1 333 Report post Posted March 26, 2019 Basically, what gear oil are members here using in their toploader 4sp transmission? I initially filled mine with Lucus 80W-90 after a rebuild and it shifted great, smooth, was quite. But read that GL-5 rated gear oils are bad for the brass parts and GL-4 rated gear oils should be used in these transmissions. I drained it and refilled it with Joe Gibbs Racing 80W-90 GL-4 rated gear oil. The trans is much harder to shift, especially downshifts from 3rd to 2nd. Are the GL-5 rated oils truly bad for the brass parts in these transmissions? Amsoil makes a synthetic 75W-90 GL-4 rated oil, but before I change the trans oil again I am curious what others are using? Quote Share this post Link to post Share on other sites
Brian Conway 264 Report post Posted March 26, 2019 I have used both of these with no problem. I run a stock RUG-AE2 4 speed and the stock OE 4 speed shifter. Brian 1 RPM reacted to this Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted March 26, 2019 Thanks. I can mail order the PennGrade from Summit Racing. Apparently, that is the Brad Penn gear oil that David Kee Toploaders recommends. I might be able to get the Sta-Lube gear oil locally. I might try the PennGrade. Hopefully, it will work better than the Joe Gibbs oil I currently have in it. Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted March 26, 2019 I bought the PennGrade Gear Oil from Summit last fall after reading about this issue either here or elsewhere. Just need to drain out the GL-5 that has been in there since 2011 when I get it out of storage and pour in the GL-4. I had bought a complete rebuild kit from David Kee and had a local guy give mine an overhaul back in 2011. I just got the correct weight gear oil from the local auto parts store not knowing I should be concerned with it being GL4 or GL5 at the time. This Toploader had never been gone through before (short of a fluid change in the mid 80's) so the rebuild made a huge difference. However it does grind going into 2nd every once in a while, so I'm hoping a swap to the correct lube stops or lessens it … vs. having to take trans out to have my guy go through it again. Doug Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted March 29, 2019 There should not be a significant change in shift feel between oil, so it sounds like something is not right. Quote Share this post Link to post Share on other sites
Brian Conway 264 Report post Posted March 29, 2019 The stock 69, one year only, 4 speed shifter does have a troublesome reverse détente assembly. First indication of a problem is the 3-2 downshift. Brian Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted March 29, 2019 11 hours ago, Brian Conway said: The stock 69, one year only, 4 speed shifter does have a troublesome reverse détente assembly. First indication of a problem is the 3-2 downshift. Brian I've got an O.E. '70 Hurst Shifter on mine plus it is 1-2 up-shift only that I get the occasional grind. Doug Quote Share this post Link to post Share on other sites
Brian Conway 264 Report post Posted March 29, 2019 Not a Hurst guy. Brian Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted March 29, 2019 16 hours ago, barnett468 said: There should not be a significant change in shift feel between oil, so it sounds like something is not right. That was my first thought and I hope that's not the situation. I would say there was definitely a noticeable difference in shifting, particularly downshifting. I don't know where noticeable changes to significant. I have done some research and apparently the Joe Gibbs GL-4 gear oils are formulated to flow easily and not leave much oil film on anything for less parasitic drag and less power loss. I will say the 80W-90 Joe Gibbs oil pours easily, almost like a 50W motor oil. The Lucus gear oil doesn't pour as easily, and leaves a slippery film of oil on everything. But the Lucus oil is GL-5 rated and twice I've contacted Lucus and both times they have said their gear oils are not for manual transmissions that use brass synchronizer rings. My guess is the Lucus oil doesn't have enough antioxidation properties to counteract the additional Sulphur in GL-5 gear oils. I don't know, that technical information is hard to get. I drained then refilled the trans with the 85W-90 GL-4 Sta-Lube gear oil that Brian Conway say's he has used with no problems. Penngrade oil had to be mail ordered and I didn't want to wait. I'll take the car out this weekend. Hopefully I'll will shift (particularly downshift) a little better than with the Joe Gibbs gear oil. For the shifter I have a Hurst Competition Plus. Not the original 1970 model, but what Hurst now offers. I'm not completely happy with it and would prefer the OEM 1970 type but they are extremely expensive when you find one is decent condition. On the current model the shifter stick is not removable which makes things a little more difficult. Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted March 29, 2019 4 hours ago, Brian Conway said: Not a Hurst guy. Brian My Hurst is stealthy though with stock boot, lever & knob up top just like yours ... got to crawl under the car to see it !! Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted March 29, 2019 52 minutes ago, 1969_Mach1 said: For the shifter I have a Hurst Competition Plus. Not the original 1970 model, but what Hurst now offers. I'm not completely happy with it and would prefer the OEM 1970 type but they are extremely expensive when you find one is decent condition. On the current model the shifter stick is not removable which makes things a little more difficult. I just started going though my old Mustang receipts (prior to 1998 when I started using Quicken). I'm slowly putting all these old receipts in a spreadsheet by date and am up to 1988 (bought the car in 1981). Anyway I got this '70 O.E. Hurst Shifter from some guy selling Mustang parts and was curious what I actually paid for it. This was the Summer of 1984 and I went to his house to look at his Mustang parts and a '69 Mach 1 project car he had for sale. Within my receipts I found a note saying ... Shifter FREE ... I don't show buying any other parts from this guy and I know it was NOT the shifter that I went to look at. Maybe because the lever was all banged up or that the threaded end for the knob was snapped off I don't know why he gave it to me for FREE and I certainly did not remember this fact from that day and seeing the note recently certainly did not jog any memory either. Thought I'd share, Doug Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted April 7, 2019 On 3/29/2019 at 5:59 AM, stangs-R-me said: I've got an O.E. '70 Hurst Shifter on mine plus it is 1-2 up-shift only that I get the occasional grind. Doug If you are using the correct oil then the grinding is 99% most likely from bad synchros. . Quote Share this post Link to post Share on other sites
shelbyshelby 52 Report post Posted April 8, 2019 From my understanding the GL5 oil is more slippery than the GL4. Thus not letting the tapered part of the synchro grab the gear and speed it up to make a grind free shift. I think the GL5 will cause shifting issues but I can’t be certain, I’ve always used the GL4. I have the sta lube in one toploader at the moment it’s never had an issue. Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted April 8, 2019 12 hours ago, shelbyshelby said: From my understanding the GL5 oil is more slippery than the GL4. Thus not letting the tapered part of the synchro grab the gear and speed it up to make a grind free shift. I think the GL5 will cause shifting issues but I can’t be certain, I’ve always used the GL4. I have the sta lube in one toploader at the moment it’s never had an issue. From what I understand depending on how fast you are trying to shift, the GL-5 oils can be too slippery for the blocker rings work correctly. I haven't had a chance to drive it yet with the Sta-Lube gear GL-4 oil in it. The Sta-Lube took much more effort to pump than the Joe Gibbs Racing gear oil. And it leaves a heavier oil film on everything. From what I have found the Joe Gibbs gear oils are designed to run off quickly to reduce parasitic losses. I guess that's fine for racing applications but maybe not as good for a street car that's rarely driven. Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted April 26, 2019 1969 Ford Shop Manual shows a magnetic drain plug in the bottom of a 4-Speed Toploader trans case … figures, my 1969 Toploader has NO DRAIN PLUG. So, what is the quickest / easiest way to drain one without a plug ?? Here is my thinking: 1) Remove Shifter & speedo cable 2) Put a jack under belhousing 3) Remove crossmember 4) put some support under trans tailshaft (jack stand or 2nd jack) 5) remove trans bolts and roll trans to let it drain out of speedo cable hole or fill hole (hopefully there is enough room in the tunnel to allow this) Thanks, Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted April 26, 2019 If your case doesn't have a drain plug, remove the lower bolt attaching the tailshaft housing to the case. The gear oil will drain through there. Put some type of sealer on the bolt threads when reinstalling it, like Permatex Aviation thread and gasket sealer. Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted April 26, 2019 56 minutes ago, 1969_Mach1 said: If your case doesn't have a drain plug, remove the lower bolt attaching the tailshaft housing to the case. The gear oil will drain through there. Put some type of sealer on the bolt threads when reinstalling it, like Permatex Aviation thread and gasket sealer. OK ... that is MUCH easier ... glad I asked !! Was wondering if maybe this is mentioned in the shop manual and I just missed it. Just skimmed through the Manual Shift Trans section again and there is no mention of this ... so again, glad I asked. Thanks, Doug Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted April 27, 2019 Yeah, the service manual doesn't mention doing that. Sometimes I wonder if Ford stopped installing drain plugs to discourage people from changing there own trans fluid. Quote Share this post Link to post Share on other sites
Midlife 814 Report post Posted April 27, 2019 Naw....magnets cost money, as well as casting a bung hole for the drain plug. Less parts, less money, more profit! Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted April 27, 2019 2 hours ago, Midlife said: Naw....magnets cost money, as well as casting a bung hole for the drain plug. Less parts, less money, more profit! hey, hows the "sunroof" in your house working out? Quote Share this post Link to post Share on other sites
Midlife 814 Report post Posted April 27, 2019 No sunroof previously, just leaking roof. The roof is now fixed. The house and garage ceiling and wall repairs will begin the last week in May once everything is removed from the dwellings. My business will be shut down for 5-8 months until repairs are completed. *sigh* 1 RPM reacted to this Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted November 20, 2019 Thought I'd follow up on this topic as I did eventually change the oil in my toploader this past summer from the GL-5 to the correct GL-4 and it still grinds on occasion shifting into 2nd. I had bought a complete rebuild kit from David Kee and had a local guy give mine an overhaul back in 2011. This Toploader had never been gone through before (short of a fluid change in the mid 80's) so the rebuild made a huge difference yet I still get the occasional grind going into 2nd. Doug Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted November 20, 2019 I guess I should update this thread. Since I refilled my top loader 4sp with Sta-Lube 85W90 gear oil that is only GL4 rated it works just fine. No strange issues at all. I found the Sta-Lube GL4 gear oil at my local NAPA store. So from my experience I'd avoid the Driven brand GL4 gear oil from Joe Gibbs Racing unless you plan on driving the car hard most of the time. The Driven brand gear oil is made to run off and not cling to surfaces to reduce parasitic drag. This makes for hard difficult shifting under normal driving. Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted November 20, 2019 On 3/26/2019 at 9:30 AM, 1969_Mach1 said: I might try the PennGrade. Hopefully, it will work better than the Joe Gibbs oil I currently have in it. Good to know about the joe gibbs oil. Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted November 20, 2019 On 4/7/2019 at 9:09 PM, shelbyshelby said: From my understanding the GL5 oil is more slippery than the GL4. Thus not letting the tapered part of the synchro grab the gear and speed it up to make a grind free shift. I think the GL5 will cause shifting issues but I can’t be certain, I’ve always used the GL4. I have the sta lube in one toploader at the moment it’s never had an issue. Yes, the GL5 can definitely cause problems in some cases. Quote Share this post Link to post Share on other sites