69 coupe from SVK

[aslanefe 282]

1 hour ago, mikee said:

Thanks aslanefe !

Yes, I was wondering  what are this brackets for. What kind of clip are they attached with?

 

Same clips used on door panels.

[staffy 72]

On 1/25/2022 at 11:04 AM, mikee said:

Windows done, all of aluminium brackets have been loose or off some way, so I had to dig out all of old glue and blue them in properly. Since I wasn't able to get the glu I saw on youtube - perfect video from WCCC, i used same as on the windshield. Seem to work perfect, time will prove it. only issue I had was how to glue then in the middle of bracket grove and in the right angle - but simple solution: 3D printed spacers with snug fit :)

Cool idea on 3D printing 

[mikee 45]

After a while some parts arrived to my eshop, so I was able to start put the car together. I bought Scott Drake lowering kit for rear end, installed tank and sending unit and modified tail lights with LED modules.   

[Vicfreg 607]

Nice Work

[mikee 45]

Meanwhile in my garage :)

After disassembly of my differential I found heavy wear on yoke seal surface. Unfortunately it was deep and after machining the original seal had only light pressure, so I hat to get some custom seal. Backlash of differential and tooth position adjusted. Finally brake parts came (except rear brake cables), and I could put everything together.

[mikee 45]

Broken heating housing repaired, and restored with new seals, finally all upholstery done and tadaaaaa. after 5 years back on own wheels!

[mikee 45]

It was raining this weekend, so I started something new – rebuild of my FMX. I ordered master rebuild kit C9ZZ-7005-MK, output shaft bushing, output and pump seal. After disassembly I inspected bearings, seals and bands. Can someone confirm my finding and answer some questions, please?

-          front band should be replaced

-          Bearing on direct drum ich chipped - should be replaced

-          is the lip on Planet bushing normal or its wear?

-          is it normal that replacement flat seal for forward clutch piston is about 1/3 thinner than original?

-          Is he wear on inside bushings (last two pics) OK?

Thanks for any answer / opinion, I’m trying to find some info on web, but except rebuild kits are even other bushing and parts hard to find

[RPM 1,056]

Did you get the Badshoe rebuild video? He goes over all that wear stuff really well. Most of the wear has to pass the finger nail test. If me, if replace all those parts, cuz you're in there anyway. 

 

[mikee 45]

no Bob, i have to download it and watch. Thanks!

[mikee 45]

Short update...

So, thanks Bob, Kens videos are great, and to work on transmission with them really fun! My front band had to be replaced / relined so I decided to buy a flexible band. Unfortunately, use of this type of band requires other strut (as for 1972-73 fmx), so I’m still not able to assembly the trany – waiting parts to come. Maybe it might help someone, so I’m posting a picture how I solved installation of direct drum piston. I used thin plastic flowerpot (cut flash at bottom ad left some rest above for pulling it out) to press the seal ring, inserted inside the drum and by constantly pressing on piston I slowly removed the pot strip.

Till struts arrive I started to rebuild side louvres an rewire the car.

[RPM 1,056]

Nice progress. Good job and thinking on the seal lip install. Rebuilding auto trannies isn't too difficult, organization and cleanliness are essential. A guy once said, if someone is smart enough to design a transmission, I should be smart enough to rebuild it. 

 

[rwcstang 177]

looking great so far, love the paint work.

[mikee 45]

Thanks Bob, thats nice saying :)

[Vicfreg 607]

Nice work!!

[mikee 45]

On 9/25/2022 at 1:27 AM, Vicfreg said:

Nice work!!

Thanks Victor,

sooo, my tranny is ready to install. I got lucky a found one „new“ upper strut for 70 and up FMX on ebay. The lower one was easy, so I made that one by myself. Adjusted according manual specs now waiting for installation.   

 

[EastYorkStang 51]

On 3/31/2022 at 1:32 PM, mikee said:

After a while some parts arrived to my eshop, so I was able to start put the car together. I bought Scott Drake lowering kit for rear end, installed tank and sending unit and modified tail lights with LED modules.   

 

Where did you get the LED modules ? Want LED tail lights for my 65 El Camino.

[mikee 45]

14 hours ago, EastYorkStang said:

Where did you get the LED modules ? Want LED tail lights for my 65 El Camino.

Hi, its cheap module from china - aliexpress / ebay:

https://www.aliexpress.com/item/1005001959116063.html?spm=a2g0o.productlist.0.0.de4a6c95A4Bao3&algo_pvid=708336d1-c8a7-4a66-94c2-843a22a47662&algo_exp_id=708336d1-c8a7-4a66-94c2-843a22a47662-23&pdp_ext_f={"sku_id"%3A"12000018229388578"}&pdp_npi=2%40dis!EUR!1.07!0.52!!!!!%402101fd4b16643416386241279eb17b!12000018229388578!sea&curPageLogUid=0oWMrz2ziqul

I tested it for a while and it did survive, but how long will it in light is still a question :)  

[mikee 45]

Just finished my light panel for rear fog, reverse and license plate light. Will be mounted in rear bumper notch and is all LED.  After I saw YT video from AtotopiaLA with Mercury Comet crashing because of brake failure, I decided to converse emergency brake to floor mounted that I'm more used to. Nice Lokar kit is way to expensive, so I'm going cheaper way:

  

[RogerC 119]

Like what you did with the license light panel. Had an idea for something similar but haven't decided how I want to do it.

I'm using this from American Shifter Co. I think I got it on ebay about 5 years ago. Don't recall the cost but think it was around $60. Also bought the accessories kit but don't recall the price.

[mikee 45]

 

On 9/28/2022 at 7:10 PM, RogerC said:

Like what you did with the license light panel. Had an idea for something similar but haven't decided how I want to do it.

I'm using this from American Shifter Co. I think I got it on ebay about 5 years ago. Don't recall the cost but think it was around $60. Also bought the accessories kit but don't recall the price.

Thanks Roger, id checked them, but prices are already on Lokar level :( but at least nice details inspiration

[mikee 45]

Hi everybody,

I started the most exciting part of my restoration – engine. My goal is nothing extraordinary, just to have reliable engine around 300-350 hp. I'd like to buy some top end kit in the future, but I can’t find anything reasonable anywhere around right now.  

Last time the engine worked was 6 years ago. As I remember, smoke was no issue, and it did run … For condition check I made cold compression test, no additional cylinder lubrication, the max. pressure was achieved after 3-4 cranks. My readings were from approx. 168 to 180 psi – what I think is pretty good. Even condition of cylinder is not so bad – the crosshatch pattern is still noticeable, and I didn’t feel any step on top of the cylinder in end position area of first piston ring. On lifters is almost none wear visible.

What’s your opinion please: Can I leave the rotation assembly as it is (crank, cam, pistons), or should I replace some parts anyway? I don’t know the condition of timing chain yet.

At this point I’m thinking to just reseal whole engine (inc. frost plugs) and just slightly port heads (remove and open overhangs on openings edges) and leave it as it is. Anyway, I think my next upgrade will be just EFI for better cold start and smoother engine run, until I start something more serious with replacing for T5 transmission.

Thanks for you suggestions...

[mikee 45]

Hi Guys ... after a while (that felt like forever)

So my lesson learned - never judge engine after removing one cylinder head :)

After I took down the second one o found some scratches in cylinder 6 and suspicious spot in cylinder 7 that could be a crack. So my optimism was gone and I knew I have to disassembly whole endine. I made penetration test of cylinder 7 - and it came out that it was no crack. The biggest disappointment was then I realized that the engine is already 0.040 over. The bearings of connection rods were also destroyed as well as on crankshaft. 

I spent hours on net to browse 351w topics and videos, what are my possibilities. To bore it over to 4.060" is to risky, to sleeve it to expensive and to find some good block for reasonable price in europe is impossible. So I decided to just refresh the engine (hone the cylinders, re ring it and change all bearings, timing, cam, lifters and oil pump), put it together so I can finish the car. With finished hone I was able to get roundness and taper to factory specs, but my bore is up to 0,002 inch over the top limit. Anyway, no option at this time, at least the crank is 0,010 under so I can let it grind to 0,020 and balance. Im looking now for parts to order. Except piston rings and camshaft it should be no problem.  

Rings - I'm not sure if I buy 0,040 over rings the gap will be not too big (my worn rings make 0,026" gap). I'm thinking to buy 0,060s and grind them to size, but I don't know if the shape of rings is already different because of bigger diameter.

Camshaft - I can't find some stock cam or some alternative in any shop (everywhere is only edelbrock performer + )