Shep69 149 Report post Posted June 25, 2017 Ok so today I started putting the mustang back together after being painted . With new rubbers Fitted I can't close the doors to match the quarter panel. The strikers are as far in as I can get them and the door sticks out about 6mm . I can force the doors into the correct spot but it's as if the striker needs to be further in. There is a bit of play in the latch , not sure if this is normal. 1 arthurow18 reacted to this Quote Share this post Link to post Share on other sites
jmlay 80 Report post Posted June 25, 2017 This is a common problem with new seals. I am sure they will relax some but can not say how much. You say there is some play in the latch, how much is some, video may help. How badly are the strikers worn? Quote Share this post Link to post Share on other sites
Shep69 149 Report post Posted June 25, 2017 41 minutes ago, jmlay said: This is a common problem with new seals. I am sure they will relax some but can not say how much. You say there is some play in the latch, how much is some, video may help. How badly are the strikers worn? I have tried a new set of strikers . No improvement . Quote Share this post Link to post Share on other sites
SM69Mach 68 Report post Posted June 25, 2017 Have you tried moving the striker out some? I had the same issue when mine was all the way in. Mine was too far in to catch completely so wasn't clamping all the way. I moved mine out some to try and start over with the adjustment it it closed much better. Just a thought on something that worked for me. Good luck. Quote Share this post Link to post Share on other sites
Shep69 149 Report post Posted June 25, 2017 26 minutes ago, SM69Mach said: Have you tried moving the striker out some? I had the same issue when mine was all the way in. Mine was too far in to catch completely so wasn't clamping all the way. I moved mine out some to try and start over with the adjustment it it closed much better. Just a thought on something that worked for me. Good luck. I can give that ago tomorrow sm69mach but the latches seam to be working . Quote Share this post Link to post Share on other sites
jjstang 51 Report post Posted June 25, 2017 I think sm69mach may be on to something. If I remember the latch has two latch points. If the seals are tight the second latch may not be catching. Moving it out a bit may allow it to catch. When you press on the door will it lay flat? That would further indicate it's not locking in to the second latch point. 2 Shep69 and SM69Mach reacted to this Quote Share this post Link to post Share on other sites
SM69Mach 68 Report post Posted June 25, 2017 2 hours ago, jjstang said: I think sm69mach may be on to something. If I remember the latch has two latch points. If the seals are tight the second latch may not be catching. Moving it out a bit may allow it to catch. When you press on the door will it lay flat? That would further indicate it's not locking in to the second latch point. That's exactly what happened on mine. When I moved it out it closed much better. Quote Share this post Link to post Share on other sites
Shep69 149 Report post Posted June 26, 2017 16 hours ago, SM69Mach said: Have you tried moving the striker out some? I had the same issue when mine was all the way in. Mine was too far in to catch completely so wasn't clamping all the way. I moved mine out some to try and start over with the adjustment it it closed much better. Just a thought on something that worked for me. Good luck. You da man SM69Mach. Worked a treat. Doors now close . As soon as jjstang mentioned two latch points i new you guys were on to it. Thanks Guys. 2 SM69Mach and JayEstes reacted to this Quote Share this post Link to post Share on other sites
Mach1 Driver 560 Report post Posted June 26, 2017 I think its because you are measuring in millimeters. Its rejecting your units of measure- that's about a quarter of an inch to us ;) 3 Shep69, RPM and JayEstes reacted to this Quote Share this post Link to post Share on other sites
SM69Mach 68 Report post Posted June 26, 2017 7 hours ago, Shep69 said: You da man SM69Mach. Worked a treat. Doors now close . As soon as jjstang mentioned two latch points i new you guys were on to it. Thanks Guys. Glad it worked out for ya. Now we need some new pics of the doors closed properly!!!! 2 Shep69 and JayEstes reacted to this Quote Share this post Link to post Share on other sites
JayEstes 172 Report post Posted June 27, 2017 Oh, and BTW- Beautiful Paint! 1 Shep69 reacted to this Quote Share this post Link to post Share on other sites
Machspeed 219 Report post Posted June 27, 2017 1 hour ago, JayEstes said: Oh, and BTW- Beautiful Paint! Gulfstream Aqua, my favorite....lol!!! 1 Shep69 reacted to this Quote Share this post Link to post Share on other sites