69Mustang16 92 Report post Posted October 8, 2016 You're getting ahead of me :) Haha, we can't wait to get some paint on this thing! Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted October 13, 2016 We fit the fronts on today We are mounting the tires onto the wheels tomorrow and will mount them all, front and back, to check our backspacing We will put all the sheet metal back on the car, apply a skim coat, then start the priming/sanding/blocking process Quote Share this post Link to post Share on other sites
prayers1 153 Report post Posted October 27, 2016 Any updates? Quote Share this post Link to post Share on other sites
JD08 42 Report post Posted October 27, 2016 I'm curious as to what the bedliner type material is. Quote Share this post Link to post Share on other sites
MikeStang 247 Report post Posted October 27, 2016 Lizard Skin or something of that nature I would guess, or scorpion or Line X perhaps Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted October 27, 2016 When we do the underside, we use Vortex which is the same thing we use for our truck beds. But for wheel wells and the underside of the fenders, we go with U-Pol. 2 MatveyAddix and Selmadox reacted to this Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted October 28, 2016 When we do the underside, we use Vortex which is the same thing we use for our truck beds. But for wheel wells and the underside of the fenders, we go with U-Pol. We used raptor liner for the underside, wheel wells and fender undersides. 1 JD08 reacted to this Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted October 29, 2016 Here are the tires mounted on the wheels We then mounted them to see how are offset/backspacing was. They were perfect. We also got the side pipe rockers set in place Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted October 29, 2016 Next we are going to lower the car to set our ride height. We are custom fabbing a lower valence so we need to set our ride height before taking those measurements and building it. Here's a rough sketch of what we are going with After that is built, the only fab work left will be the shaved door handles. Then we can finally get to prime/block/sand work Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted October 29, 2016 Looks like our side skirts fit perfect. Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted October 29, 2016 Looks like our side skirts fit perfect. That they did! Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted October 29, 2016 I think this is the first 69-70 with our skirts :) 1 69Mustang16 reacted to this Quote Share this post Link to post Share on other sites
sixt9stang 36 Report post Posted October 31, 2016 Very cool build. Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted October 31, 2016 Very cool build. Thanks! We can't wait to get some paint on it. Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted November 1, 2016 Custom Lower Valence update Also, close to how it'll sit.. Should sit slightly lower when all is said and done Quote Share this post Link to post Share on other sites
nickjames138 15 Report post Posted November 2, 2016 That's nasty! 1 69Mustang16 reacted to this Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted November 2, 2016 That's nasty! Agreed :) Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted November 2, 2016 We are also doing some reshaping to the rear valence 1 SWPruett reacted to this Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted November 2, 2016 That front valance would sell like hotcakes if reproduced. Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted November 2, 2016 That front valance would sell like hotcakes if reproduced. But then it wouldn't be a one of a kind ;) Quote Share this post Link to post Share on other sites
mustangstofear 608 Report post Posted November 2, 2016 Send it to me so I can produce it :) 2 RPM and 69Mustang16 reacted to this Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted November 3, 2016 But then it wouldn't be a one of a kind ;) As good as it looks, it shouldn't be. 1 69Mustang16 reacted to this Quote Share this post Link to post Share on other sites
SWPruett 83 Report post Posted November 4, 2016 Excellent build! I am impressed with the fit of the rear bumper, especially when it looks like not a lot of cutting was required! Any pics of what was done for it? Keep those updates coming! Quote Share this post Link to post Share on other sites
69Mustang16 92 Report post Posted November 4, 2016 Excellent build! I am impressed with the fit of the rear bumper, especially when it looks like not a lot of cutting was required! Any pics of what was done for it? Keep those updates coming! Thanks! Sure, I can get those pics to you let me snap a few Will do! 1 SWPruett reacted to this Quote Share this post Link to post Share on other sites
Guillaume69 150 Report post Posted November 5, 2016 We used raptor liner for the underside, wheel wells and fender undersides. We used exactly the same product for my car. Bullet prof and water tight! After 10,000 miles on the road, it still looks brand new and shiny. Great build, by the way. Keep them pics flowing our way!! G 1 RPM reacted to this Quote Share this post Link to post Share on other sites