Suggestions for exhaust tips

[JayEstes 172]

All,

 

I have converted a single exhaust system (302) to a dual 2.25in diameter.  I bought a re-pop rear valence and am now looking to put the final decor on the tips.  I think I would prefer a bolt on solution, but I could be convinced to go weld-on, however I am going to have to pay someone to put them on for me and that will drive up the cost.

 

I'd prefer to pay something in the $20-$50 per tip range, and I'd prefer stainless steel, but will consider chrome if I can be convinced it won't just rust out over the first year.  I also like the rolled tip/dual walled options. I'd like a slash tip, but could be convinced otherwise.  Here is some stuff I am considering:

 

Nice option, but pricey and only weld on:

http://www.ebay.com/itm/STAINLESS-TRIPLE-CHROME-UNIVERSAL-EXHAUST-TIP-2-25-ID-x-3-OD-4-Long-HAVE-2-C-/280385113310?hash=item4148414cde:m:mHxbbvqSn3XHFDvjANfbAuw&vxp=mtr

 

A cylindrical bolt on (kinda pricey):

http://www.ebay.com/itm/2-5-Inlet-Bolt-On-Screw-Oval-Rolled-Slanted-304-Stainless-Steel-Exhaust-Tip-/261672397311?hash=item3cece3e9ff:g:ZggAAOSw9N1VjBkR&vxp=mtr

 

I like this Mach 1 style, but I think these are too big (wide) to fit well in the stock cut-out on the rear valence.

http://www.ebay.com/itm/Stainless-Steel-9-Long-Double-Wall-Exhaust-Tip-w-2-5-Inlet-3-Dual-Outlet-/131553275992?hash=item1ea12fb058:g:dhwAAOSwDNdVnobP&vxp=mtr

 

This one is cheap, and just might fit.  It's in the mach 1 style.

http://www.ebay.com/itm/Stainless-Steel-9-Long-Rolled-Exhaust-Tip-w-2-25-Inlet-3-x-4-Dual-Outlet-/201385484095?hash=item2ee3829f3f:g:feIAAOSw-vlVnoO1&vxp=mtr

 

Then there is a nice oval one, that might fill the cutout nicely, but doesn't reflect any heritage look

http://www.ebay.com/itm/Stainless-Steel-Tail-Pipe-Exhaust-Tip-2-5-Inlet-4-5-x-3-5-Outlet-8-Long-/141531711459?hash=item20f3f287e3:g:ftwAAOSwc3ZUqury&vxp=mtr

 

Many of the above are from 1 vendor on e-bay  If you've used or have any experience with them, I would appreciate hearing about it - good or bad.

 

Thanks for your thoughts...

 

[RPM 1,190]

Any of the middle 3 would work for me. I'm too lazy to walk the 40' into the shop to measure the valance opening to see if they fit.

[RogerC 136]

I've got a pair of Pypes SS tips that came with the Pypes exhaust system for my 06. I didn't use them cause I didn't like the large size and bought some smaller tips instead. Am about to put them on craigslist for $40. They're 4" tips to fit 2.5" pipe and have a slight slash to them though hard to tell in the pic. I don't think mine have the slots on the pipe end, have to look tonight when I get home. My replacements were bolt on and I slotted them to fit on my pipes.

[rwcstang 201]

I have these on mine, http://www.summitracing.com/parts/sum-690052

[RogerC 136]

Mine are slotted, look exactly like the pic.