RPM 1,190 Report post Posted March 30, 2016 I'm sure this won't be the last time I ask all y'all for help identifying parts as I put this car back together. I'm guessing something to do with electrical? The short end the brass ribbon spring has a male terminal, the other end has rub scratches on it. I can't make out the part number below the 5/16 bolt head. I know as soon as it's identified I'll reply with a DOH! Nice cell phone pics huh? Muchas gracias. Quote Share this post Link to post Share on other sites
1969_Mach1 333 Report post Posted March 30, 2016 Goes on the emergency brake assembly. It's the switch to control the brake light in the dash when the emergency brake is applied. That feature was optional in 1969 but the switch was installed regardless. The light it would operate is the same brake warning indicator light controlled by the switch on the pressure differential/proportioning valve. My Mach 1 has that switch on the emergency brake and no wiring to connect to it so my car did not have that optional feature. 1 Mach1 Driver reacted to this Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted March 30, 2016 DOH! Yep, now I member. Thank you much! Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted March 30, 2016 I think it's a muffler bearing. 1 Mach1 Driver reacted to this Quote Share this post Link to post Share on other sites
Brian Conway 264 Report post Posted March 30, 2016 ..muffler bearing friction acceleration modifier ? Seriously never seen that part before. It must be on the hidden/other side of the parking brake assembly ? My car does not not have the warning light. Brian Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted March 30, 2016 That is actually an option, so not all cars have it. Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted March 30, 2016 Hmm...didn't know the muffler bearing was an option. Always thought it was an urban legend, learn sumpin ever day. Quote Share this post Link to post Share on other sites
rwcstang 201 Report post Posted March 30, 2016 flux capacitor Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted March 30, 2016 Ya, the only reason it rang a bell was cause I was the yahoo who removed it. 1 JayEstes reacted to this Quote Share this post Link to post Share on other sites
Rsmach1 71 Report post Posted March 30, 2016 I think it's a muffler bearing. That was my guess as well..... Quote Share this post Link to post Share on other sites
barnett468 418 Report post Posted March 31, 2016 That was my guess as well..... You're only saying that because I did. Quote Share this post Link to post Share on other sites
ralt962 11 Report post Posted April 19, 2018 I know this is an old post, but someone might know here. If the car originally came with the switch, but it was no longer there, (so no wire was connected) would the dash brake light come on? Just did a complete restore of a Mach 1. New drums front and rear, new lines. I bleed the system but I still have the dash warning light on. I'm going to try to re bleed the system and see if it balances out. Its not driveable yet so I don't have an idea how well the brakes will work. Quote Share this post Link to post Share on other sites
69RavenConv 286 Report post Posted April 19, 2018 The dash light you are seeing is illuminated through a switch on the distribution block under the hood. It's meant to indicate a pressure imbalance between the front and back brake lines. It can be a bear to extinguish under the best circumstances and in bad circumstances it freezes up and won't go out without a rebuild. If you're confident in your brakes you can simply unplug the 2-pin connector on the brass distribution block and it will go out. Otherwise you must bleed each circuit (front and back) alternately until you get the slug in the distribution block to center itself and open the switch. The switch on the e-brake pedal lights up the brake light that was part of the "convenience group" option package. On cars without the convenience group, I don't think you get a light for the e-brake. Quote Share this post Link to post Share on other sites
ralt962 11 Report post Posted April 21, 2018 On 4/18/2018 at 9:51 PM, 69RavenConv said: The dash light you are seeing is illuminated through a switch on the distribution block under the hood. It's meant to indicate a pressure imbalance between the front and back brake lines. It can be a bear to extinguish under the best circumstances and in bad circumstances it freezes up and won't go out without a rebuild. If you're confident in your brakes you can simply unplug the 2-pin connector on the brass distribution block and it will go out. Otherwise you must bleed each circuit (front and back) alternately until you get the slug in the distribution block to center itself and open the switch. The switch on the e-brake pedal lights up the brake light that was part of the "convenience group" option package. On cars without the convenience group, I don't think you get a light for the e-brake. Thanks for the picture. That eliminates one issue. Going to have to work on the bleeding and see if I can balance it. I did rebuild the distribution block, new switch and seals. I found an old spec book and it shows this light as being a dealer installed option in the convenience group. Looks like they had a number of dealer installed items. Quote Share this post Link to post Share on other sites