Vicfreg 584 Report post Posted September 22, 2021 Dude, that airbox is kickass. What a great job with the vision and then fabricating it. Well done! 1 paulb reacted to this Quote Share this post Link to post Share on other sites
paulb 108 Report post Posted October 3, 2021 On 9/22/2021 at 10:23 AM, Vicfreg said: Dude, that airbox is kickass. What a great job with the vision and then fabricating it. Well done! Thanks, Quote Share this post Link to post Share on other sites
paulb 108 Report post Posted November 28, 2021 Rear seat / side panels and door trims back from trimmers, came up well, almost ready for the road 1 Grabber70Mach reacted to this Quote Share this post Link to post Share on other sites
paulb 108 Report post Posted December 26, 2021 We’ll after having it for 13 years and rebuild over the last eight,she’s finally registered and driving , it’s been a long road. 5 stangs-R-me, SWPruett, RPM and 2 others reacted to this Quote Share this post Link to post Share on other sites
SWPruett 67 Report post Posted December 27, 2021 Beauty! 1 paulb reacted to this Quote Share this post Link to post Share on other sites
paulb 108 Report post Posted January 3 Just finished the stereo and boot install 1 Grabber70Mach reacted to this Quote Share this post Link to post Share on other sites
Vicfreg 584 Report post Posted January 16 Paul, going back a bit to a mention in your post about "central locking". Can you explain what you did and post a few pictures. I am very interested in this. Thanks, Vic Quote Share this post Link to post Share on other sites
Grabber70Mach 89 Report post Posted January 21 Nice job it looks great. 1 paulb reacted to this Quote Share this post Link to post Share on other sites
paulb 108 Report post Posted January 21 On 1/16/2022 at 11:49 PM, Vicfreg said: Paul, going back a bit to a mention in your post about "central locking". Can you explain what you did and post a few pictures. I am very interested in this. Thanks, Vic Hi Vic, it’s a kit that’s installed, can get them on eBay ,I mounted the solenoid towards the back of the door and attached the rod to the inside snub button rod, I ran wires inside from each side to the control box under the dash, previous post shows how I did the extra wires running from doors to pillars, only photo I can give you is of the actuators if you want Quote Share this post Link to post Share on other sites
Vicfreg 584 Report post Posted January 22 OK thanks, let me take a look at the pictures appreciate it Quote Share this post Link to post Share on other sites
Mach1 Driver 431 Report post Posted January 23 On 1/3/2022 at 6:01 AM, paulb said: Just finished the stereo and boot install That's impressive. I saw the spaghetti on page 4 and another shot of the fuse block (and computer?) on page 5. Is that an aftermarket harness are you using? I've thought about putting the fuses in the trunk for easier access. How did you route/hide all the wire in the floor areas through the cabin? I didn't see any photos. Quote Share this post Link to post Share on other sites
paulb 108 Report post Posted January 23 6 hours ago, Mach1 Driver said: That's impressive. I saw the spaghetti on page 4 and another shot of the fuse block (and computer?) on page 5. Is that an aftermarket harness are you using? I've thought about putting the fuses in the trunk for easier access. How did you route/hide all the wire in the floor areas through the cabin? I didn't see any photos. This is the only photo I have atm, wires for control box all run under the console on the trans tunnel, rear seat has a decent gap on the hump. Their encased in a zip loom protector, so if need I can open it up easily. The main battery leads run up either side of the floor 1 Mach1 Driver reacted to this Quote Share this post Link to post Share on other sites