Daves69Coupe 10 Report post Posted September 11, 2012 which way do you pull the brake release to dis-engage parking brake. Ive pushed the p brake down but can get it to release. Lines are new but mechanism under dash is OEM. Quote Share this post Link to post Share on other sites
Thunderscrash 10 Report post Posted September 12, 2012 I'm retry sure you pull it toward you. I had this issue just the other day but I can't remember just get under there, locate the mechanism and mess with it until it releases. Quote Share this post Link to post Share on other sites
rangerdoc 22 Report post Posted September 12, 2012 You pull the handle straight towards you. Sometimes the handle gets bent because people step on it instead of the pedal, which makes it difficult to disengage. 1 Mach1 Driver reacted to this Quote Share this post Link to post Share on other sites
Nightowl 10 Report post Posted September 12, 2012 Under this same subject, how would you get that mechanism out? I want to sand blast it, and repaint it. I see 3 bolts, and a pin like device that may hold the cable in, so how do you disconnect the cable from the mechanism? Richard Quote Share this post Link to post Share on other sites
LoneWolf2U 136 Report post Posted September 12, 2012 Loosen the tension spring under the car for the E brake cable. This allows the cable to move freely and the pin to come out. Quote Share this post Link to post Share on other sites
Flanders 46 Report post Posted September 12, 2012 can someone post a good pick of the mechanism, in the car? When I put mine back together, I'm pretty sure I didn't get the return spring in the right spot. My release works, but not very well! Quote Share this post Link to post Share on other sites
Nightowl 10 Report post Posted September 12, 2012 Since I have the dash out, let me snap a few. I should have them up this evening. Quote Share this post Link to post Share on other sites
Nightowl 10 Report post Posted September 13, 2012 (edited) Here are a couple of pics. Edited September 13, 2012 by Nightowl Quote Share this post Link to post Share on other sites
Flanders 46 Report post Posted September 13, 2012 thanks! I'll be comparing that to mine soon :) Quote Share this post Link to post Share on other sites
Nightowl 10 Report post Posted September 13, 2012 If anyone sees anything wrong with those pics, let me know. Someone said the handle sometimes get bent?:smile: Quote Share this post Link to post Share on other sites
Lemon Owner 11 Report post Posted September 14, 2012 That handle is bent terribly. To fix it you just ask your friends, or as I did my wife to release the hand brake. The foot pedal snaps back up into the released position and belts your fingers onto the release handle. Hurts like hell or so my wife says. In my defence I did warn her not to release it by hand and to use her toes but she wouldn't listen. :w00t: Quote Share this post Link to post Share on other sites
Nightowl 10 Report post Posted September 15, 2012 Here are a couple more with it removed. Quote Share this post Link to post Share on other sites
bomccorkle 12 Report post Posted September 16, 2012 Mine is bent as well. I have hax the thought of replacing with a c4 corvette style release but havnt worked put the details as of yet..... Quote Share this post Link to post Share on other sites
stangme428 33 Report post Posted September 16, 2012 Someone wanted to set the parking brake on mine.... I said open the door and step on the the parking brake pedal .... They opened the door steeped on the release handle .... Didn't work they said... Ok remind me not to let you drive my car when I'm done.... LoL..:biggrin: When I tried to gently bnd it back..... Snap... I think I'm moving towards a 2005 handle.. Quote Share this post Link to post Share on other sites
Nightowl 10 Report post Posted September 16, 2012 I'll heat it up with the torch, then try to put it back into place. If not, they sell the replacement for 80 some bucks. Quote Share this post Link to post Share on other sites
Daves69Coupe 10 Report post Posted September 17, 2012 so I had a chance to start messing with parking brake and see why it wont release. I got underneath and started pulling handle and I could see the mech sliding back and forth like it should but it wasnt disengaging the foot brake. Quote Share this post Link to post Share on other sites
Nightowl 10 Report post Posted September 18, 2012 :smile:I started by taking it out and using MACH1RIDER'S suggestion. Under the car, you will see where it hooks up to the cable to the back brakes. There are 2 nuts you must take off. The first one is a small one, then there is a 3/8 nut that holds the spring and the connector. I couldn't get the cable from the parking brake to stop turning, so I took a vise grips, and put it on the cable. That helped alot, and the spring came off. That will loosen up everything else. I then took the 3 bolts out, took out the pin that holds the cable to the parking brake, gave it a small tug so the cable moved a little, then pushed the ball out of the connector. Now remember, I have my lower dash and pad out, so its alot easier to do it, but I think with a little time, some cuss words, you can get it out.:smile: Quote Share this post Link to post Share on other sites
Daves69Coupe 10 Report post Posted September 18, 2012 i dont wanna get it out. Just disengage brake Quote Share this post Link to post Share on other sites
Jlawl49 0 Report post Posted March 2, 2022 I found that a flat head works well to release it if you have a bad spring or bend on your release. I'll try to post a pic later with the setup and direction of pull. Quote Share this post Link to post Share on other sites
Mach1 Driver 560 Report post Posted March 2, 2022 7 hours ago, Jlawl49 said: I found that a flat head works well to release it if you have a bad spring or bend on your release. I'll try to post a pic later with the setup and direction of pull. Just so you are aware, the previous post is ten years old. Quote Share this post Link to post Share on other sites
Mountaineerfan 44 Report post Posted March 2, 2022 I thought this was an old post.... Mine releases fine, but I have found I have to push the release handle back in by hand so I can set the brake again. Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted March 2, 2022 Funny that someone resurrected this old thread. The parking brake assembly in my car is a replacement as I myself once caught the release lever with my foot and bent the hell out of it !! Thankfully the one in it now was a spare I saved from a parts car. I do think the release handle hangs too low and have often thought I should try and tweak it up closer to the bottom of the dash so I don't accidentally do in this one someday. Just one of many things on my endless "to-do" list. Doug Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted March 2, 2022 Maybe this resurrected thread is an omen for me to install mine. 1 stangs-R-me reacted to this Quote Share this post Link to post Share on other sites
Mach1 Driver 560 Report post Posted March 2, 2022 Brakes?? We don't need no stinking Brakes! 1 stangs-R-me reacted to this Quote Share this post Link to post Share on other sites
EastYorkStang 63 Report post Posted March 7, 2022 Mine is a short 4x4 block of wood. Quote Share this post Link to post Share on other sites