DocWok 30 Report post Posted June 3, 2023 I'm looking to make the scoop functional as a cold air intake on my 69. Have looked at the few pictures on the net, but they are usually taken at an angle so hard to gauge an accurate measurement of the pie-cuts. Would anyone have a hood with factory cut outs that they could put a tape against the holes to get a clear picture. It's a long shot I know, but worth to ask just in case I get lucky. Quote Share this post Link to post Share on other sites
Ridge Runner 1,113 Report post Posted June 3, 2023 About the best i could do ,its buried behind a few parts Quote Share this post Link to post Share on other sites
DocWok 30 Report post Posted June 3, 2023 Thanks Ridge, much appreciated. That will help, clearest picture I've seen so far. Quote Share this post Link to post Share on other sites
rwcstang 201 Report post Posted June 4, 2023 8 hours ago, Ridge Runner said: About the best i could do ,its buried behind a few parts Ridge, would you happen to know the dimensions of this? Quote Share this post Link to post Share on other sites
Ridge Runner 1,113 Report post Posted June 4, 2023 I will have to see if i can dig it out Quote Share this post Link to post Share on other sites
ThePoose 37 Report post Posted June 6, 2023 I have the measurements if y'all can wait till later tonight or in the morning so I can make them readable. 2 DocWok and rwcstang reacted to this Quote Share this post Link to post Share on other sites
ThePoose 37 Report post Posted June 6, 2023 Pardon the crude drawing. Took all measurements from the center of the pie cuts. Meaning that 22 1/4 is from the center of the pie cut on the cuts closest to the front of the hood. It was just getting messy. Mirrored measurements are all the same. All the pie cuts are the same size, the lengths of the two sides shown are if the lines continued straight instead of curving. The shapes of the forward two cuts are different on the radius, which you can see on the photo Ridge sent. If you have to cut the underside of the hood for the turn signals, those rear two oval measurement will be different from the top of the hood shown here. 2 DocWok and rwcstang reacted to this Quote Share this post Link to post Share on other sites
GearHeadPeter 4 Report post Posted July 1, 2023 Thanks for posting this as I've wanted to do the exact thing on my 69 hood. Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted July 2, 2023 Here is how I did mine back in the 80's before I'd ever seen dimensions ... or an actual Ford cut out on a '68-69 Mustang. Got the idea from the 1969 Fairlane/Torino Hood and related parts drawing in my Mustang Illustrations Catalog ... pdf of this is also below. Doug HOOD & RELATED 1969-70.pdf Quote Share this post Link to post Share on other sites
Ridge Runner 1,113 Report post Posted July 2, 2023 I used to have a couple of 68 69 cobra torinos ,the hood cut out is the same as the mustang Quote Share this post Link to post Share on other sites
stangs-R-me 120 Report post Posted July 2, 2023 53 minutes ago, Ridge Runner said: I used to have a couple of 68 69 cobra torinos ,the hood cut out is the same as the mustang I figured it probably was, but had never seen one out in the wild other than that drawing back at that time. I think mine actually looks better in that all 4 holes are symmetrical !! Doug Quote Share this post Link to post Share on other sites
Vicfreg 772 Report post Posted November 28, 2023 Found this in my archives. Shows the original non-shaker ram-air set up, with just the Mach 1 style hood scoop feeding the air cleaner.... Cobra Jet Ram Air Patent.pdf Quote Share this post Link to post Share on other sites
Vicfreg 772 Report post Posted November 28, 2023 Cobra Jet Ram Air Patent.pdf Quote Share this post Link to post Share on other sites