Caseyrhe 650 Report post Posted February 4, 2021 I know they are different, but are the 70’s just a tad larger? Current one in my brothers car are loose on the spindle hole and the replacements I bought are fitting the same. I was thinking we pulled them off a 68 cougar back in the early 80’s but I’ve slept since then and he damn sure doesn’t know. Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted February 4, 2021 Since they are a taper, wouldn't the taper angle have to be off to not fit? If the hole was just larger would not the stud just fit further into the hole? Quote Share this post Link to post Share on other sites
Caseyrhe 650 Report post Posted February 4, 2021 Fits to far in the hole to where it won’t cinch up. Shaft just spins inside the spindle hole. It’s like a 18 yr old tapping a 70 year old whore, loose as all get out. Have the 70 tie rods ordered now and will be in tomorrow, so will keep you posted. Worse case I’ll just use a popsicle stick and rubber bands, to get it up and in, lol. 1 RPM reacted to this Quote Share this post Link to post Share on other sites
Kris 90 Report post Posted February 4, 2021 Yes the 70 tie rods are larger at the tapered part that goes into the spindle. They do make tapered sleeves you can put on 69 tie rods to use them. I think mustang Steve sells them. Quote Share this post Link to post Share on other sites
Caseyrhe 650 Report post Posted February 5, 2021 70 tie rod ends did the trick. Next question for the forum in 5, 4, 3, 2, 1 Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted February 5, 2021 Keep those questions coming, I'm learning all kinds of things. I haven't used the stock outer tie rods since I rebuilt my car. These are 1970 spindles with a Mustang II taper adjustable stud. Quote Share this post Link to post Share on other sites
Caseyrhe 650 Report post Posted February 5, 2021 What kind of hokey pokey dolly system you got working holding the back of your motor up. I've seen it all now!! 1 69RavenConv reacted to this Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted February 6, 2021 Hokey pokey? That sounds like Texas talk. Dude, that pic was taken about a hunert years ago and you want me to remember what was going on then? I did use those wheel dollies to hold the body up and be mobile, but never with the motor in it. No laughing Phil, I do have the power to ban you :) Quote Share this post Link to post Share on other sites
Caseyrhe 650 Report post Posted February 6, 2021 So do you remember what you did yesterday? Well do ya? Quote Share this post Link to post Share on other sites
Midlife 814 Report post Posted February 6, 2021 Hell, he can't even remember his name or when he's supposed to see his Parole Officer... 1 Caseyrhe reacted to this Quote Share this post Link to post Share on other sites
RPM 1,190 Report post Posted February 6, 2021 Randy, dude, you said you wouldn't tell anyone about the parole deal. Quote Share this post Link to post Share on other sites
Midlife 814 Report post Posted February 7, 2021 Fake news! I said it as fake news, folks! Nothing to see here...move along... Quote Share this post Link to post Share on other sites
jmlay 80 Report post Posted February 7, 2021 On 2/3/2021 at 10:02 PM, Caseyrhe said: Fits to far in the hole to where it won’t cinch up. Shaft just spins inside the spindle hole. It’s like a 18 yr old tapping a 70 year old whore, loose as all get out. Have the 70 tie rods ordered now and will be in tomorrow, so will keep you posted. Worse case I’ll just use a popsicle stick and rubber bands, to get it up and in, lol. Throwing a pickle down the hallway... 1 Caseyrhe reacted to this Quote Share this post Link to post Share on other sites