hawkdriver

Hey group. First I’ll start out by saying hopefully this is not too broad of a question I just want to start seeing possible recommendations to begin to narrow things down. I will have all the time in the world to research as I’m currently deployed and planning a build. 69 coupe 351w pretty stock. FMX TRANS. Currently have a weiand stealth intake. Looking for a top end setup to work with my current intake. Hoping for low to mid 400 hp. Right now just looking for heads cam carb to get me in the ballpark. Soon I’ll be researching headers and exhaust. Figured engine was the starting point. Want to keep cost down as much as I can as it’s still a coupe love to hear what you recommend

Iv have been having some unlock issues and hoping you all could help me out. I think iv narrowed it down to a spring. Was wondering if anyone knew of an aftermarket one available. Worse case if anyone would have one or a whole assembly the would be willing to sell. I’d hate to but a new $60 lock set for a $2 spring. See attached. Thanks

Hey guys I’m installing a Hayden dual stage fan relay to a escort early 90s fan. Someone suggested a bigger relay between the Hayden and fan due to the amp draw of the high speed fan does anyone know the high speed fan startup amp draw is there a recommended relay Seems the common referee relay is Bosch 75 as it has the diode Lastly can anyone describe or provide diagram of how to to include this bigger relay not trying to burn my car up in this one. thanks

Flange uneven, mainly dented around bolt holes slightly, noting major just want any problems moving forward

Got it, Thanks for the help all, It was done by putty knife and shimming it out as i went. Thanks for all your help. However i did find it bent slight, not sure if it was from me or PO as it did seep a little. Any advice on flattening it out prior to putting it back on. Thanks again for all the help

Thanks for the input, No its black "the right stuff" and funny you mentioned that, i tried it and it didn't well, maybe ill try slightly thinner. I too though that was the ticket.

Thanks, Yea i been doing that just not a whole lot of luck, i was thinking more towards a chemical removal. Thanks ill keep at it though

Hey Guys, Need a bit of help, i was told PO used permatex the right stuff for trans pan, i have to change oil and filter, but cannot get the damn thing off. I tried cutting through the gasket to no avail, tried gasket remover even though i was told it wouldn't work, i don't have the ability to remove the trans to work on on it so I'm under car, and cannot for the life of me get the pan removed without damaging pan or trans. Any suggestion would help, Thanks. FMX if it matters

What type of metal is the "chrome" grill molding, for polishing purposes? Any advice on cleaning and polishing this trim? Thanks

How did you wire up that fuse block i have been seeing that and would like to give it a try?

Hey, Im installing a Hayden 3654 setup controller to my taurus fan, i do not have A/C. I once read that this 'green A/C clutch" wire from the controller could be used as an under dash override in the event of temp sensor failure. Can anyone confirm this and explain how i would wire this up. I pressure i need a 12+ source and to extend this green wire to a switch and to ground out the switch. Where can i easily pull 12+ from in the cabin of fuse box? Thanks for your help.

Shelby, Thats exactly what i bought after much research, this will undoubtedly provide much more power to whatever light you use even OEM lights or at least save your existing wiring and switch from the power draw. Unfortunately i cannot give you a review as mine is still in box and im in Afghanistan. I am very interested in the lights you have chosen however, this is the one pice to this upgrade i am not complete with. I have seen alot in excess of 100$ for the set on ebay, but am not thrilled with the bulbs nor the price, You have any recommendations on lights. I will be home in just over an month and this is the first thing i am upgrade so if i beat you to it ill let you know how the harness works out.

Im in the process of cleaning up my bay, i would like to remove the starter solenoid and voltage regulator, complete remove them from the system. I have a 3G alternator and a PMGR mini starter. I have done research and many say to keep the solenoid regardless of the mini starter. Is this correct? IF anyone has done this can you please explain in vivid detail on how to run the wiring or at least what to do with the current wire in the system i have now. I would love to do away with this and clean up the rats nest of wire. Thanks for your help

2 part question; Does anyone have any advice on installing the chrome trim that goes around the grille on 69. I have tried the wire clips from vendors and none seem to work or stay put. Is there any other fabrication that has worked for this. Second, any good advice on polishing this chrome up. Thanks

Looking for some help form the detail experts. I have what i believe to be a single stage paint job ( i will determine such when i return from deployment) what im looking for if it is determined to be single stage paint is how to bring out a nice shine. I have cleaned it prior to deployment and hit it with quality spray wax and noticed a hazing on the flat black racing stripes the paint was fine with it however i attempted to keep it off the stripes. My question is how to bring out a nice shine while not creating a haze over the flat black. In knowing or thinking it is single stage i am hesitant to use a clay bar or even a rubbing compound on it thinking it may e too abrasive. Looking for some expert guidance as i have never dealt with a singe stage before. Just want this to get shined up nice in the spring. Thanks