Debbie
Members-
Content Count
25 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Store
Everything posted by Debbie
-
Mach1 driver I took your advice and ordered the grommets from LMR was so happy to finally get the door grommets but unfortunately the picture on the website was very deceiving this is what I received size of a quarter
-
No I don’t have a mig welder
-
I installed air shocks and they keep loosing air pressure poor design in the air line hook up two o rings and a cap holds them in place Is there another option? like braided hoses?
-
I wanted to be able to know my actual temp and oil pressure so I installed gauges on my pillar But I want my gauges to work in the cluster also is this possible? my mechanic told me it’s not possible to have the gauges working in the cluster and the pillars gauges at the same time. cant I just install a T?
-
I wanted to be able to know my actual temp and oil pressure so I installed gauges on my pillar But I want my gauges to work in the cluster also is this possible? my mechanic told me it’s not possible to have the gauges working in the cluster and the pillars gauges at the same time. cant I just install a T?
-
Hi How can I raise the front seats in my mach1 and make them go forward a inch or two? I know use a cushion
-
Hi How can I raise the front seats in my mach1 and make them go forward a inch or two? I know use a cushion
-
No not yet
-
I removed the metal strip that holds the felt in to clean it up did you remove yours?
-
I installed a new ignition switch yesterday, went to start the car, the entire switch turned around inside the dash Having problems keeping the tab on the switch in the bracket slot When I have the switch in the slot and go to screw on the retaining nut it slips out very frustrating
-
I replaced my harness and the mechanic threw out the door harness with the grommets
-
Do you have the grommets?
-
No I do not have the grommets on the wire harness because I installed a new painless performance harness for the entire car. My mechanic threw out the old harness and That’s why I don’t have them.
-
My niece has a 1968, 289 coupe she wants to sell, the body is in ruff shape all complete but has been sitting out in the weather. She doesn’t have the time to restore it. Her father had a major stroke and spends all her time taking care of him. location Jersey Shore
-
Hi all I have a 9” factory rear in my mach1 and want to put in a posi rear. I was told if I install a 411 I will lose either take off speed or top end speed so I was also told a 373 Dana will take care of take off speed and top end and suggestion? Thank you Deb
-
Does anyone know where to buy the rubber door grommets that the door light wiring goes threw from the door jamb
-
Does anyone know where to buy the felt that goes on the window stop?
-
My parking lights go off when I put the headlights on I think they should stay on for safety and it looks nice I went to YouTube and found that by putting a jumper in the light switch you can make them stay on because then they would be working off the tail lights I will post the diagram
-
Yes I have the grande interior but i have a Mach1 its a fastback
-
Hi Does anyone have a picture or know where the dome light is located my 1969 mach1 Grande interior Also dome light wire get power from? Thank you Deb
-
I live in NewJersey Does anyone know where I can get my ac vent re-chromed? My car didn’t have AC so I installed it but the kit came with plastic vents so I found original vents on eBay painted the side vents black but the center dash vent is chrome
-
Thank you for showing me the picture when I plug my harness for the light and plug the switch into the harness it doesn’t work. This is what I did to make it work I attached the hot wire coming from the light harness to the housing of the switch, now it works but if the switch touches any metal such as the hole in the glove box where it’s installed, the map light comes on so I covered the switch so it wont touch metal and it works?? I don’t know why it wouldn’t work the original way
-
I attached my light to the glove box switch to the housing of the switch because it has current coming from it from the map light, but the problem is when the glove box switch touches the metal dash when you install it in the hole, the map light come on?
-
I’ve had all kinds of issues with installing a painless wiring harness. My issue now is installing a glove box switch and glove box light I contacted painless performance about this installation. The tech said to plug the glove box switch into a lead coming off the map light. ok I did, my question is where does the glove box light plug in? There is also a male/ female plug on the clock harness that the manual tells you not to use?