Jump to content

first69

Members
 View Profile  See their activity

  • Content Count

    93

  • Joined

  • Last visited

Community Reputation

19 Good

See reputation activity

About first69

  • Rank
    Mustang Owner
  • Birthday 08/06/1957

Converted

  • Location
    il- wi border
  • Occupation
    retirered
  1. first69
    So as of now I don't think I can find new glass that will fit properly. So I hope to find a good quality oem out there
  2. first69
    I may be missing it but I don't see the bump. I have tried adjusting the foot of the guide rods in and out. As well as put a shim at the top of the guide rod to bring it out towards the interior. As I stated I have both in glass that is just heavily scratched and it worked perfect. The repot glass rolls up very difficult and as I said it was scraped the door skin. There is no room for the Rubber seal. So now I am just trying to find a good OEM glass clear. I would think my Hardware is correct because the OEM glass works correctly
  3. first69
    It's odd that the glass that is in the car works perfect. But I am open any ideas to make this work.
  4.    lapedVem reacted to a post in a topic: 70 Bolt in Glass
  5.    wapedVem reacted to a post in a topic: 70 Bolt in Glass
  6.    first69 reacted to a post in a topic: 70 Bolt in Glass
  7.    first69 reacted to a post in a topic: 70 Bolt in Glass
  8. first69
    The glass hadthe correct look just when you rolled it up it would go against the door skin and you could not adjust it out
  9.    Zefevinee reacted to a post in a topic: 70 Bolt in Glass
  10. first69
    Two were from CJ Pony and one from PS glass and Wisconsin. They were new.
  11.    ncdruroSor reacted to a post in a topic: 70 Bolt in Glass
  12. first69
    I purchased three different passenger Fastback Windows clear. all three did not fit. The curvature was incorrect. So I am looking for a decent passenger Fastback Clear Window. Hope that one of you can help me out with this. Thank you
  13.    JimmyByday reacted to a post in a topic: Driveshaft
  14.    stephanienl69 reacted to a post in a topic: Driveshaft
  15. first69
    I have 52 and a half inches from Center of U-joint to center of U-joint. I found a 51 inch from an explorer. Is 1 1/2 inches too much play?
  16.    ernaqe3 reacted to a post in a topic: 72 351c exhaust manifold
  17.    winifredng69 reacted to a post in a topic: 72 351c exhaust manifold
  18. first69
    My driver side is D5AE-9431-AB. Passenger side which is cracked is D20e-9430-3a. Not sure if the driver side is correct that's why I was looking for a pair but really just need the passenger side that is cracked
  19. first69
    I am fine in a couple different numbers for that year on the manifolds
  20. first69
    2v
  21. first69
    Looking for stock exhaust manifold for my 1972 351c. This is an engine that is in my 69 Fastback. Anyone on here have any that would like to ship
  22. first69
    Found a place in Madison Wisconsin that vacuum Chrome. It is pricey.600 For gauge bezel and clock bezel
  23. first69
    How hard was it to apply? Did you take any photos of the process?
  24. first69
    Most of the Chrome is gone on my dash cluster and clock bezel. What have you use to repaint or do you get them rechromed.
  25. first69
    Looking for teak wood clock trim
×
×
  • Create New...