-
Content Count
208 -
Joined
-
Last visited
-
Days Won
2
Content Type
Profiles
Forums
Calendar
Store
Everything posted by 390mach1
-
thanks for the help
-
My original power steering pump wasn't working so I got a rebuilt ACI power steering pump put it on last night and it works great but it leaks from the threaded stud I tighten it as much as I can and it still keeps leaking. has anyone had this issue and know how to fix it?
-
What does everyone think of this radio http://www.virginiaclassicmustang.com/67-73-Mustang-AM-FM-iPod-Doc-USB-Radio-P482195.aspx
-
Hi all I'm looking for the jumper wire that goes from the plug in in the trunk and goes to the out side of the car and goes to the sending unit.
-
I'm having this issue right now too. I've replaced the circuit board on the back of the cluster the constant voltage regulator, and all new led blubs and bulb sockets. At first I only had one blub light up in the center od my cluster and I tried moving bulbs around and ended up only getting one turn signal bulb to work. below is the link to CJ for the LED bulbs that I got. Maybe I should try just regular bulbs? http://www.cjponyparts.com/scott-drake-instrument-panel-led-set-1971-1973/p/SD7173GABL/
-
The second picture we used tied into the harness without splicing it for the Rocketman tach conversion and I didn't want to mess up the stock tach harness. So what wire would hook to the back of the radio?
-
Hi all I need a little help with my dash wiring, I sent it all out to midlife to be redone and its working great! every light and turn signal is working but I have a couple question on a few wires that I don't know what they are. I have 3 or 4 bright green wires with female ends on the and I'm not sure what plugs into them. also I have a grey wire with a 90 deg. bend push on type and I don't know what that goes too. I took a couple pictures of them so hopefully that will help. Another issues I have is I put a new circuit board on the back of the cluster and also a new voltage regulator and new led light kit from CJ Pony and I only got 1 or 2 blubs working in the cluster now... :( any help or advice would help.. Thanks!
-
Thanks for all the help guys I'm probably going to go with the Magnaflow 2.5" Kit and see if I can put a Mach 1 style Tail pipe on it.
-
RCWSTANG do you got any pictures under your car?
-
I have a 393W stroker, no staggered rear suspension. I'm looking for something with nice sound and also I would like to have the pipes tucked up nice to the floor so it doesn't hang down.
-
What Exhaust system is everyone running? Did you buy a kit or have a system built? I have FPA headers and would like to run 3" to the mufflers to a 2.5" over the rear and out stock style Mach 1 tail pipes? If you got pictures that would be great!
-
sent you a text an will send a email as well.
-
Thanks Vanscooter
-
What are the best subframe connectors that don't hang down and show for a 69 Mustang Fastback?
-
looking for a 69 351W air cleaner base.
-
Is anyone planning on being on the PowerTour? I'm going to be doing 4 stops not sure which car hoping to have my Mach done. If not will be taking my dads 67 fastback
-
I'm not sure how to check I as I currently don't have the tach hooked up and its acting like this. is there anything I can check?
-
Thanks guys as always I love the feed back! finally getting my butt in gear to finish the car as a buddy is getting married and wants to drive a few stops on the power tour.
-
Is there anyway to rebuild a factory tach? my tech always seems to jump to 1,000 RPM I have it all tore apart and cant seem to see any place to adjust.
-
Barnett468 I'm not sure on how you would like the measurement made?
-
So I do have a victor Jr here are a few pictures
-
Thanks for all the help I should be back in the barn tonight and try to get some kind of better measurements/pictures
-
Do you have any measurements that the shaker should be angle? I am running factory mounts (after market as my was originally a 390) I am running an AOD tranny so I have an after market cross member
-
I'm not sure what brand it is I got it from a guy at a ford national show in Carlisle PA, its supposed to be a big block set-up. I will get measurements tonight or tomorrow. thanks or everones help.