Jump to content


Popular Content

Showing content with the highest reputation since 04/23/2019 in all areas

  1. 4 points

    69 Mach 1 / 408W

    Getting closer.....
  2. 3 points

    69 Convertible build

    That will make a nice donor car for the rebuild. :)
  3. 3 points

    69 Mach 1 / 408W

  4. 3 points

    Finally got a Marti Report

    Wether it’s a 1 of 1 or 1 of 7000, it’s a 69 Stang. It’s 50 years old!! I can’t count the number of people I’ve sent to the chiropractor due to them snapping their heads around to get a glimpse of my 69 or 70 while out for a cruise. What about that poor guy under his wife’s thumb wishing he could have a older Stang. I hear so many comments about people either not liking the coupes and or the fastbacks. It’s 50 years old, still running, still snapping necks, and you know there’s prob not even a third of them still around. All mine, even the 82, are all 1 of 1 in my book and yours should too. Built not bought!!
  5. 2 points

    New Valves in not-new heads

    If you correctly blue the valves i.e. apply it correctly, very thin - tap the valve up and down a couple of times without rotating it and it shows a correct seat, then lapping the valves will achieve nothing extra.
  6. 2 points

    Wheel Play – Options?

    Unfortunately, steering boxes can not be fully rebuilt, and typically are never as good as new when they are "rebuilt", because the worm gears wear and are not available, and when they wear, the steering will still have play, but some people try to reduce this play by over tightening the adjustment. This being said, a steering box that has play in the bearings will have less play after they are replaced. If one wants to properly rebuild a steering box that has worn gears, they can send the gears out to have then welded and refaced, however, this is a fairly expensive operation, but it shouldn't need to be done again until long after most of us are dead and buried.
  7. 2 points
    Bolted on a wilwood master cylinder, powder coated the dash vents and now I'm replacing the felt lining
  8. 2 points

    My Son Mike's 69 Mach 1 Restoration

    who's gonna mow the other half of that lawn :-)
  9. 2 points
    Mike and I had a big day this past weekend. We finally got the car off the rotisserie and all painted with rust inhibitor. Just have a little lower quarter work to finish that could not be done on rotisserie.
  10. 2 points

    In need of help - Engine noise

  11. 2 points
    Here's what it looks like electrically. As Mid said it could be the neutral safety switch, or you could be right and its the ignition switch. You could put the car in park or neutral, turn the key to "on" and jump from S to the battery lug on that side of the solenoid. If it starts but dies after you remove the short, then its either B to C in the ignition switch, the tach if you have one, or the resistor wire.
  12. 2 points
    Check your neutral safety switch (jiggle the shifter while key is in crank if automatic); broken wire in NSS jumper if manual tranny.
  13. 2 points
    Now that the engine is out, the tranny is much easier to take out and overhaul it as well. Don't forget to get your radiator flushed, recored, and painted nice and neat. And then there is that small paint smudge that needs to be fixed...I know it gnaws at you every time you look at it...Tee Hee Hee!
  14. 2 points
    While you're at it...
  15. 2 points

    Bump steer?

    Lowering the upper control arms 1" and modifying them to move ball joint back to increase the caster improved the handling on my cars.
  16. 2 points
    Mach1 Driver

    The Ultimate Kill Switch ?

    On Page 1 of the PDFs below, it shows three methods to disable the ignition. Page 2 shows three ways to disable the fuel, and page three shows how to use a magnet and reed switch to turn those systems off. The advantage of a magnetic reed switch is that it can be hidden behind any plastic part and no one will know where it is or how to turn it off. With a normal kill switch you run the risk that the thief will find the switch. This won't outsmart a determined thief, particularly one with a tow truck, but it will stop most. These are the magnets on my key chain. These little guys are very strong for their size and are normally used as jewelry clasps. They come in pairs with a small through hole down the axis and a larger hole that goes partway down on the other end. I used 30 lb mono-filament, tied a knot and pulled it into the oversize hole. Pull on the loop and you can separate and hold one of the magnets. If you don’t want to hang the magnets off your key chain you could just let the magnet grab on to a chunk of steel somewhere in the car and it won’t go anywhere. I prefer to remove the magnet from the vehicle. The reed switch sits to the right of the magnets. It is small but the electrical specs are more than adequate for the job. This is a demonstration of how well the magnet and reed switch work. Here we have an easily removable piece of plastic trim. The reed switch is attached to the inside with a piece of Scotch tape. The ohmmeter is connected to each side. The magnet is attached to the ohmmeter with scotch tape and supported by the mono-filament line. The magnet is about 1/2” away from the reed switch and has successfully closed the switch- you can see from the ohmmeter that it is not an open circuit but has 14.6 ohms. This rather high resistance is probably due to my ratty old alligator clips, but even this is more than adequate to operate the relay shown in the PDFs, and get you on your way. KILL SWITCH PAGE3.pdf kill switch page1.pdf kill switch page2.pdf
  17. 2 points
    Nice work there, i am up on the central coast, empire bay.
  18. 2 points

    15x10 Magnum 500s

    A bit late, I know, but yes I have just put this setup on my car. Wheel Vintiques 15x10s with 5.5" backspace. According to CJ Pony, I bought their last 2 wheels and they are now out of production. Sumitomo HTR 2000 295/50/R15 tyres. These have a 12mm (0.5 inch) narrower section width (sidewall-to-sidewall) than the same size BF Goodrich TAs and I prefer the tread pattern over the TAs. I am running aftermarket 1" lower leaf springs from Eaton Detroit Springs. The quarter panel lips have been rolled slightly as a precaution but it's not necessary for me (the rear of the car sits high enough and I don't carry back seat passengers over bumpy roads). Internally I have 35mm clearance between the leaf spring and the tyre. And yes, that's how you spell "tyre" ;-) Externally, the sidewall lines up exactly with the wheel arch lip. All said and done, perhaps 6" backspace would have been better and given me more clearance between the rubber and the quarter panel. And you can always reduce 6" backspace to 5.75" by adding a 0.25" spacer (if you dare). Pictures attached...
  19. 2 points
    You sure this isn't your problem?
  20. 2 points

    67-70 Cougar

    Maybe you need to change the name of the company to "Cougars to Fear" or "Ford/Lincoln/Mercury to Fear" or "Nothing to Fear but Fear Itself!"
  21. 2 points

    Make parking brake switch

    Here is how you reproduce the not yet reproduced 69-70 parking brake switch. Make the ABS body and the end by 3D printing. Make a bending jig to bend the beryllium copper contact to right shape and bend the contact strips. Heat treat the contact. Assemble and secure the parts. You are done. Changed the original design a little bit so the contact does not break due to fatigue like the originals did. Cycled the black switch 2500 times on the 70 Cougar pedal I have off the car; it did not brake and did not stop working so installed it on my 69 Grande. Left to right on the pictures below are; broken original switch, 3D printed ABS parts, contact, final product.
  22. 2 points

    Ignition kill switch with key

    She never leaves my sight when she's out, but I carry a 9mm
  23. 1 point

    69 Convertible build

    Me too. Probably my favorite body style besides the 67-70’s.
  24. 1 point

    In need of help - Engine noise

    Great news. In your video, it sounded like the old familiar fuel pump noise.
  25. 1 point

    In need of help - Engine noise

    You nailed it. So grateful I thought I was up for another rebuild. I took the old fuel pump off and blanked the hole. Quiet as a mouse. Thanks.
  26. 1 point

    I dont know how i feel about this mustang,,

    Fixed your typo.
  27. 1 point

    My Son Mike's 69 Mach 1 Restoration

    That’s what I have 2 boys who build cars for!
  28. 1 point

    Fitech vs Sniper vs ?

    I went with the Holley Sniper with Holley EFI fuel tank and the Holley Dual-Sync Distributor, all is controlled via the integrated ECU and touch screen. I have it connected to a performance built 4R70W AOD trans, which sync's to the ECU as well as the trans ECU (adjustable shift points). Engine is a 408 Stroker Windsor.
  29. 1 point
    Looks great. I went with Evaporust as it got good reviews and was available close to home. It’s applied, bagged, and we will see tomorrow how it did. Also got my cam bearing tool today and I knocked out the old cam bearings. I have everything I need to finish the short block now. Waiting on springs and valves to do the heads.
  30. 1 point

    In need of help - Engine noise

    Thanks, I got one today.
  31. 1 point

    1968 Cougar

    The original color was Autumn Green, not a very attractive color. We had the owner check out the new 2019 Bullitt green, he did and we are going with that. I think it will look really nice.
  32. 1 point

    Head gasket issue? (No it was a wiped cam)

    CV from everything I have seen after 24 years in the auto business that milky gunk in the radiator & the inside of the valve cover sounds to me like you got coolant in the oil.
  33. 1 point

    1969 Coupe Restomod...long time

    Over the years...very slow progress. Lots of life lived between infrequent time spent on the Mustang.
  34. 1 point
    He’s the devil...
  35. 1 point

    What did you do to/for your Mustang today?

    and the hood opened the next day, and so on, and so, and.......
  36. 1 point

    Bump steer?

    It may or may not be bump steer. Worn steering and suspension pieces, and toe out can cause your symptoms. Lowering these cars from stock ride height often adds to the bump steer these cars already have. After doing the Arning upper control arm drop, adding a bump steer kit, and doing my own alignment, my 69 handles pretty darn well.
  37. 1 point

    Finally got a Marti Report

    So I've owned the car for more than 35 years and I ordered a Deluxe Marti Report earlier this week. Built Friday December 6th 1968. A nothing special mustang and why I've had no reservation whatsoever of modifying this car.
  38. 1 point

    Who has an aftermarket brake booster?

    I know of them, everyone likes their service. My problem is that questionable cores (rust/pitting/missing parts) are being sold for hundreds of dollars and it's a gamble. I am not against an original at all, but I have a problem shelling that kind of money out. I haven't been able to find a reasonably priced core or original, because everyone seems to know they aren't that common.
  39. 1 point
    Nice car.
  40. 1 point

    Windshield Washer Pump

    The way I have done them is to use a needle nose pliers to pull the star retainer ring out first then you can use a regular pair of pliers & grab the pump on the raised part where the wiring plugs in & pull the old pump out.
  41. 1 point

    fastback rear window gasket

    Yeah, that's what she said as well.
  42. 1 point

    Hedman Elite 88658 reviews

    I will have to chime in for the FPA longtubes. Expensive, but you get what you pay for. Fits my 70 with a 351w, cable clutch, and borgeson steering box. Never thought i'd get longtubes to fit in that space, but they dropped in perfectly. fit and finish is top notch and still look great 10 years later.
  43. 1 point

    Alignment Question

    For street -0.5 camber, max + caster you can get (I am running +8.8 caster at the moment with my modified upper control arms, but with stock control arms and strut rods you can get about +3.5 caster) and 1/16 to 1/8 toe in. No more than 0.25 degrees difference between right side and left side on camber and caster.
  44. 1 point

    Fox body AC system in a 1969 Mustang?

    Great idea though, jkish. If the underdash component fit, theoretically you could fab up duct work and get pressure hoses made up to fit. You'd still have to figure out the control board - would you use the Fox control panel or aftermarket or ____? As the others have said, by the time you do all that, factoring in your time, you'd probably be better off going with a COTS (commercial off the shelf) system. Nate
  45. 1 point

    Fox body AC system in a 1969 Mustang?

    The compressor is maybe the only thing that would work in your coupe. If you have an AC car already, then it probably would work, but like Mike said, getting the fittings and hoses could be a problem. If you do not have a factory AC car, then go with a new kit ( maybe without the compressor??)
  46. 1 point

    Fox body AC system in a 1969 Mustang?

    Would probably take more effort than its worth honestly, especially after removing the stuff from one car and getting new hoses made up to fit, re-sealing everything etc... Just spring for the classic auto Air kit and be done with it.
  47. 1 point

    Lower Radiator hose spring

    I dont know why none of the hoses come without a spring in the hose anymore. the rubber is no stronger and probably softer than before, so i doubt technology will be there for us when it collapses and overheats. So in case you cant find one ( like me) here is how i made mine in 2 min. 3/32 stainless steel tig wire 1" black pipe and vise grips/ Problem solved! Pics are out of order, but you get the point,
  48. 1 point

    It is Time

    Funny how you forget stuff. I completely forgot about this 70 notch back I owned for maybe 6 months in Houston around maybe 1985??. Was just looking at old pictures. Was a factory shaker, 4 bbl and 4 gear. I wasn't making enough money to rub two nickels together and simply couldn't afford to keep it running. One of my proudest moments in life was when my beautiful bride grabbed major 2nd gear rubber in this car! Really wish I kept it, but I don't see how it would have been possible with just starting out life and upcoming family. It's a good memory.
  49. 1 point
    Nice car you got there, mate! I'm actually wondering, if it's not a secret, of course, how much did it cost you up until this point, and how much do you think is everything gonna cost? I mean, from now on. Thanks for the updates and hopefully we'll see more from you! Congratulations, my friend!
  50. 1 point
    Really nice work!

  • Create New...